|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
very fast detailed and accurate hope to do business again
;
This was precisely what I was looking for. Complete and good quality!
 ;
This is the ONLY copy of this manual I could find for a realistic price. Even Panasonic could not provide me with one.
The PDF is a very good copy and it helped me diagnose and find the fault with the unit I have.
;
Very complete and well reading drawings. Documentation is essential for successful repairs.Good documentation, with all that is necessary. This manual was what I was waiting with all the information necessary for the repairing I need it for. You must buy it if you want to do repairs or simply understand how it works.
;
Excellent service manual includes everything is need to repair this radio-caseete, how to disassemble, wiring diagram, all , waiting time until the download was only a few hours. I'm going to buy service manuals from here, are cheap and very good.Thank you.
<M2> UPPER ASS'Y(G)
C1 E
F 605 COVER(TOP/UPP)L COVER(TOP/UPP)R D1 C2 606 604 D2 J H C1 607 B 612 MONI.LOCK ASS'Y
611
MONITOR ASS'Y(G) (Refer to the Exploded view for this part.) 601 616 D1
SUB OPE UNIT
A
610 UPWARDS C2 U.CASE ASS'Y 602
(WR601a) F
617 PASTE
D2
FRAME(UPPER) ASS'Y E SOLDERING 2 POINT 603
G A 614 SCREW * SPEAKER 609 608 BRACKET(SPEAKER) * Mark*: This part was deleted on the way of production.
B
J H
G 613 CONCLUSION SCREW TORQUE TABLE PART.NO 611 ANOTHER SCREW TORQUE 0.2 ±0.01 N�m 0.08 ±0.01 N�m PROCESSING SUB OPE FPC. DRAWING FOR SPACER STICKING. 626 COVER(TOP/UPP)R COVER(TOP/UPP)L 615
VALLEY FOLDING VALLEY FOLDING MOUNTAIN FOLDING
UPPER ASS'Y(G) LYH20626
PROCESSING MONITOR FPC.
PROCESSING SUB OPE.
3 ±1 mm
VALLEY FOLDING AFTER PASTING SUB OPE PUSH TO THIS SLASH PART. MOUNTAIN FOLDING
SPACER(A)
DON'T STICK OUT SPACER IN SUB OPE FPC. VALLEY FOLDING
PASTE SPACERS NOT TO COVER THESE HOLES. STICK TO U.CASE. SHEET STICK ALONG THE REINFORCEMENT BOARD OF FPC. PASTE SPACER INSIDE BKT(UPPER). DON'T RUN A GROUND TO A LEVEL DIFFERENCE OF UPPER CASE. SOLDER 2 POINT MOUNTAIN FOLDING
SPACER(A) SPACER(A)
618 623
SHOULD BE COVERED THIS CONVEX.
SPACER(A) 620
DON'T STICK OUT SPACER IN UPPER CASE. LESS THAN 0.5mm
3 ±1 mm
STICKER
625
624 SPACER(A) 621
SPACER(A)
SHEET STICK ALONG THE CORNER OF FRAME. STICK FPC SO THAT THERE MAY BE NO CREVICE BET MEEN THE HOLE OF IT IN THE RIGHT SIDE OF THE HOLE RING.
PASTE SPACER THIS CONVEX IN UNDER SIDE. DON'T BE SEEN SPACER OUTSIDE OF UPPER CASE.
THE SIDE OF THE HOLE RING IS MET. THESE HOLES CAN BE SSEN.
619
DON'T RUN A GROUND OF UPPER CASE. DON'T SEPARATE.
SPACER(A) SHEET(SHIELD) 622
STICK SPACER THAT FPC MAY BE PRESSED DOWN.
Fig. 1-2-2c UPPER ASS�Y(G)
1-5
|
|
|
> |
|
