|
Who's Online
There currently are 5678 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
;
Très-très bon site, facile, très bon prix.
Au futur besoin, je n’hésiterais à faire appel à vous.
Merci
<M2> UPPER ASS'Y(G)
C1 E
F 605 COVER(TOP/UPP)L COVER(TOP/UPP)R D1 C2 606 604 D2 J H C1 607 B 612 MONI.LOCK ASS'Y
611
MONITOR ASS'Y(G) (Refer to the Exploded view for this part.) 601 616 D1
SUB OPE UNIT
A
610 UPWARDS C2 U.CASE ASS'Y 602
(WR601a) F
617 PASTE
D2
FRAME(UPPER) ASS'Y E SOLDERING 2 POINT 603
G A 614 SCREW * SPEAKER 609 608 BRACKET(SPEAKER) * Mark*: This part was deleted on the way of production.
B
J H
G 613 CONCLUSION SCREW TORQUE TABLE PART.NO 611 ANOTHER SCREW TORQUE 0.2 ±0.01 N�m 0.08 ±0.01 N�m PROCESSING SUB OPE FPC. DRAWING FOR SPACER STICKING. 626 COVER(TOP/UPP)R COVER(TOP/UPP)L 615
VALLEY FOLDING VALLEY FOLDING MOUNTAIN FOLDING
UPPER ASS'Y(G) LYH20626
PROCESSING MONITOR FPC.
PROCESSING SUB OPE.
3 ±1 mm
VALLEY FOLDING AFTER PASTING SUB OPE PUSH TO THIS SLASH PART. MOUNTAIN FOLDING
SPACER(A)
DON'T STICK OUT SPACER IN SUB OPE FPC. VALLEY FOLDING
PASTE SPACERS NOT TO COVER THESE HOLES. STICK TO U.CASE. SHEET STICK ALONG THE REINFORCEMENT BOARD OF FPC. PASTE SPACER INSIDE BKT(UPPER). DON'T RUN A GROUND TO A LEVEL DIFFERENCE OF UPPER CASE. SOLDER 2 POINT MOUNTAIN FOLDING
SPACER(A) SPACER(A)
618 623
SHOULD BE COVERED THIS CONVEX.
SPACER(A) 620
DON'T STICK OUT SPACER IN UPPER CASE. LESS THAN 0.5mm
3 ±1 mm
STICKER
625
624 SPACER(A) 621
SPACER(A)
SHEET STICK ALONG THE CORNER OF FRAME. STICK FPC SO THAT THERE MAY BE NO CREVICE BET MEEN THE HOLE OF IT IN THE RIGHT SIDE OF THE HOLE RING.
PASTE SPACER THIS CONVEX IN UNDER SIDE. DON'T BE SEEN SPACER OUTSIDE OF UPPER CASE.
THE SIDE OF THE HOLE RING IS MET. THESE HOLES CAN BE SSEN.
619
DON'T RUN A GROUND OF UPPER CASE. DON'T SEPARATE.
SPACER(A) SHEET(SHIELD) 622
STICK SPACER THAT FPC MAY BE PRESSED DOWN.
Fig. 1-2-2c UPPER ASS�Y(G)
1-5
|
|
|
> |
|