|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
6
EN
Hook on.
GETTING STARTED
Power
This camcorder�s 2-way power supply system lets you choose the most appropriate source of power. Do not use provided power supply units with other equipment.
1
2 Push in.
CHARGING THE BATTERY PACK
1
BATTERY RELEASE Switch REFRESH Button REFRESH Lamp CHARGE Lamp
Make sure the battery pack is attached to the camcorder. Hook its end to the camcorder 1 and push the battery in until it locks in place 2. �If the battery pack is attached in the wrong position, a malfunction may occur. Set the Power Switch to �OFF�. Connect the AC Adapter to the camcorder 3, then connect the Power Cord to the AC Adapter 4. Plug the Power Cord into an AC outlet 5. The CHARGE lamp on the camcorder blinks to indicate charging has started. When the CHARGE lamp stops blinking but stays lit, charging is finished. Unplug the Power Cord from the AC outlet. Disconnect the AC Adapter from the camcorder.
2 3 4
3 To DC IN
connector
Battery pack
Power Switch To AC outlet
To Detach The Battery Pack . . . .... slide BATTERY RELEASE and pull out the battery pack.
NOTES: � During charging or discharging, the camcorder cannot be operated. � Charging and discharging is not possible if the wrong type of battery is used. � When charging the battery pack for the first time or after a long storage period, the CHARGE lamp may not light. In this case, remove the battery pack from the camcorder, then try charging again. � If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one. � Using the optional AA-V15EK AC Power Adapter/ Charger, you can charge the BN-V11U/V12U/V20U/ V400U battery pack without the camcorder. However, it cannot be used as an AC adapter.
5 4
Battery pack BN-V11U* BN-V12U (optional) BN-V20U** (optional) BN-V400U (optional)
AC Adapter
Charging time approx. 1 hr. 10 min. approx. 1 hr. 10 min. approx. 1 hr. 50 min. approx. 3 hrs. 40 min.
* GR-SXM55 only. **Provided with GR-SXM607 only.
REFRESH:
Charging a battery with some charge remaining reduces that battery�s capacity. Perform the procedure below to fully discharge the battery pack before recharging. 1. Perform steps 1 through 3 of �CHARGING THE BATTERY PACK�. 2. Press REFRESH on the camcorder for over 2 seconds. The REFRESH lamp on the camcorder blinks to indicate discharging has started. 3. When discharging is finished, charging automatically starts and the CHARGE lamp blinks. When you are not using a battery pack for a long period of time, be sure to fully discharge it before storing because leaving a battery with some charge left over also reduces performance.
For other notes,
pg. 44
|
|
|
> |
|
