|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
TROUBLESHOOTING
Before consulting your JVC dealer, please check the following to see if you can correct the problem yourself.
Vertical white lines appear when shooting a very bright object. � This sometimes occurs when the contrast between the back-ground and the object is great. It is not a defect of the camcorder. Bright, crystal-shaped spots appear in the LCD monitor and the viewfinder. � Sunlight is directly entering the lens. This is not a defect of the camcorder. Coloured bright spots appear all over the LCD monitor or the viewfinder. � The LCD monitor and the viewfinder are made with highprecision technology. However, black spots or bright spots of light (red, green or blue) may appear constantly on the LCD monitor or in the viewfinder. These spots are not recorded on the tape. This is not due to any defect of the unit. (Effective dots: more than 99.99 %.) Animation or Time-Lapse is not available. � Before recording in the Animation mode at the very beginning of a tape, set the camcorder to the Recording mode for about 5 seconds, so that the tape runs smoothly. Using the Fade-in function at this point is a good way to begin an animated programme ( pg. 21, REC TIME/INT. TIME in SYSTEM MENU). The tape is running, but there is no playback picture. � The TV has not been set to its VIDEO mode or channel. � If A/V connection is used, the TV�s VIDEO/TV Switch has not been set to VIDEO.
Playback picture is blurred or interrupted. � The video heads are dirty or worn out. Consult your nearest JVC dealer for head cleaning or replacement. The tape stops during fast-forward or rewind. � The Counter Memory Function has been activated ( pg. 14, �Counter Memory�). The date and time displays disappear. � If you remove the power source from the camcorder while the power is on, all settings and selections are erased. Make sure to turn the camcorder�s power off before disconnecting the power source. The tape will not eject. � The battery pack is running low. � If the LCD monitor is not open over 60 degrees, the EJECT switch t does not function.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.); and then re-connect it and proceed as usual from the beginning.
Warning Indications
(high) (exhausted) : Displays the battery remaining power level. As the battery power comes close to nil, the battery indicator blinks (battery power warning). When the battery power is exhausted, power turns off automatically. :Blinks when no cassette is loaded, or when the erase protection tab is not in the position that allows recording. TAPE END: Appears when the tape ends during recording, playback or fast-forward. LENS CAP: Appears for 5 seconds after power is turned on if the lens cap is attached. CONDENSATION OPERATION PAUSED PLEASE WAIT: These 2 warnings appear alternately every 3 seconds if condensation occurs. In this case, all functions except tape eject and power on/off are disabled. Remove the tape, turn the unit off (without removing the power supply), wait a few minutes for the warnings to clear, and turn it on again. HEAD CLEANING REQUIRED USE CLEANING CASSETTE: These 2 warnings appear alternately every 3 seconds if dirt is detected on the heads during recording. In this case, use an optional cleaning cassette. If the warning remains after cleaning, consult your nearest JVC dealer. E01�E06 UNIT IN SAFEGUARD MODE REMOVE AND REATTACH BATTERY: The error indications (E01 � E06) show what type of malfunction has occured. If an error indication and warning appear, turn the unit off, remove the power supply (battery, etc.) and wait a few minutes for them to clear. When it does, you can resume using the camcorder. If the indication remains, consult your nearest JVC dealer.
29
|
|
|
> |
|
