|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
GV 30�, GV 50�
Laufwerk
Fett (75988 061 7800) auf schattierte Flächen auftragen
30000
Flachbandleitung
22000 Stator 30000 21000 Rotor 11600 Massefeder 11500 Kohlestift 11000 Bandtrommel
Fig. 8.37 Fig. 8.35 8.13 A/W-Kopfeinheit (50200) � Schraube (Pos. 50210) lösen und A/W-Kopfeinheit (50200) gemä� Fig. 8.36 in Pfeilrichtung drücken und nach oben abnehmen. Hinweis: Loch U der A/W-Kopfeinheit (50200) nach der Position des Stiftes V auf dem Laufwerkchassis ausrichten. Anschlie�end den Bandlauf und die Trackinglage (X-Wert) einstellen (siehe Punkt 9. "Einstellungen").
50200 50210
11000
U
Y
10400
V
10400
Fig. 8.38 Achtung: Nach dem Einbau des Rotors (21000) muss die Phase des Kopfrads eingestellt werden. Die Löcher W des Kopfrads und X des Rotors müssen gemä� Fig. 8.39 auf der gleichen Seite liegen. Die Schrauben (30000) für den Rotor und den Stator (22000) mit einem Drehmoment von 2.5 bis 3.5kg/cm befestigen.
Fig. 8.36 8.14 Bandtrommel � 2 Schrauben (30000) herausdrehen, Stator (22000) abnehmen und Bandtrommelerdungsfeder (11600) entfernen (Fig. 8.37). � Dreht man jetzt das Laufwerk um, fällt der Kohlestift (11500) heraus (Fig. 8.37). � 2 Schrauben (30000) herausdrehen und Rotor des Motors (21000) entnehmen (Fig. 8.37). � 3 Schrauben (10400) auf der Unterseite des Laufwerks lösen und die Bandtrommel kpl. (11000) herausnehmen (Fig. 8.38). Einbau: Beim Einbau die Bandtrommel kpl. (11000) auf den beiden Passstiften Y der Montagefläche positionieren (Fig. 8.38). Die Schrauben (10400) mit einem Drehmoment von 3.9 bis 4.2kg/cm festziehen.
11200 Kopfrad
W
21000 Rotor
X
Fig. 8.39
GRUNDIG Service 5 - 13
|
|
|
> |
|
