|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ filippo611@aol.com
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
GV 30�, GV 50�
Laufwerk
Fett (75988 061 7800) auf schattierte Flächen auftragen
30000
Flachbandleitung
22000 Stator 30000 21000 Rotor 11600 Massefeder 11500 Kohlestift 11000 Bandtrommel
Fig. 8.37 Fig. 8.35 8.13 A/W-Kopfeinheit (50200) � Schraube (Pos. 50210) lösen und A/W-Kopfeinheit (50200) gemä� Fig. 8.36 in Pfeilrichtung drücken und nach oben abnehmen. Hinweis: Loch U der A/W-Kopfeinheit (50200) nach der Position des Stiftes V auf dem Laufwerkchassis ausrichten. Anschlie�end den Bandlauf und die Trackinglage (X-Wert) einstellen (siehe Punkt 9. "Einstellungen").
50200 50210
11000
U
Y
10400
V
10400
Fig. 8.38 Achtung: Nach dem Einbau des Rotors (21000) muss die Phase des Kopfrads eingestellt werden. Die Löcher W des Kopfrads und X des Rotors müssen gemä� Fig. 8.39 auf der gleichen Seite liegen. Die Schrauben (30000) für den Rotor und den Stator (22000) mit einem Drehmoment von 2.5 bis 3.5kg/cm befestigen.
Fig. 8.36 8.14 Bandtrommel � 2 Schrauben (30000) herausdrehen, Stator (22000) abnehmen und Bandtrommelerdungsfeder (11600) entfernen (Fig. 8.37). � Dreht man jetzt das Laufwerk um, fällt der Kohlestift (11500) heraus (Fig. 8.37). � 2 Schrauben (30000) herausdrehen und Rotor des Motors (21000) entnehmen (Fig. 8.37). � 3 Schrauben (10400) auf der Unterseite des Laufwerks lösen und die Bandtrommel kpl. (11000) herausnehmen (Fig. 8.38). Einbau: Beim Einbau die Bandtrommel kpl. (11000) auf den beiden Passstiften Y der Montagefläche positionieren (Fig. 8.38). Die Schrauben (10400) mit einem Drehmoment von 3.9 bis 4.2kg/cm festziehen.
11200 Kopfrad
W
21000 Rotor
X
Fig. 8.39
GRUNDIG Service 5 - 13
|
|
|
> |
|
