|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Even if the PDF is a scan, I can read the information I need.
The price is affordable and the service (mail sending) is very fast.
Thanks ! Regards. William (Fan of Kenwood)
 ;
Very good quality original datasheet!I like this amazing website!!!!!!
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
 ;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
GV 30�, GV 50�
Laufwerk
Fett (75988 061 7800) auf schattierte Flächen auftragen
30000
Flachbandleitung
22000 Stator 30000 21000 Rotor 11600 Massefeder 11500 Kohlestift 11000 Bandtrommel
Fig. 8.37 Fig. 8.35 8.13 A/W-Kopfeinheit (50200) � Schraube (Pos. 50210) lösen und A/W-Kopfeinheit (50200) gemä� Fig. 8.36 in Pfeilrichtung drücken und nach oben abnehmen. Hinweis: Loch U der A/W-Kopfeinheit (50200) nach der Position des Stiftes V auf dem Laufwerkchassis ausrichten. Anschlie�end den Bandlauf und die Trackinglage (X-Wert) einstellen (siehe Punkt 9. "Einstellungen").
50200 50210
11000
U
Y
10400
V
10400
Fig. 8.38 Achtung: Nach dem Einbau des Rotors (21000) muss die Phase des Kopfrads eingestellt werden. Die Löcher W des Kopfrads und X des Rotors müssen gemä� Fig. 8.39 auf der gleichen Seite liegen. Die Schrauben (30000) für den Rotor und den Stator (22000) mit einem Drehmoment von 2.5 bis 3.5kg/cm befestigen.
Fig. 8.36 8.14 Bandtrommel � 2 Schrauben (30000) herausdrehen, Stator (22000) abnehmen und Bandtrommelerdungsfeder (11600) entfernen (Fig. 8.37). � Dreht man jetzt das Laufwerk um, fällt der Kohlestift (11500) heraus (Fig. 8.37). � 2 Schrauben (30000) herausdrehen und Rotor des Motors (21000) entnehmen (Fig. 8.37). � 3 Schrauben (10400) auf der Unterseite des Laufwerks lösen und die Bandtrommel kpl. (11000) herausnehmen (Fig. 8.38). Einbau: Beim Einbau die Bandtrommel kpl. (11000) auf den beiden Passstiften Y der Montagefläche positionieren (Fig. 8.38). Die Schrauben (10400) mit einem Drehmoment von 3.9 bis 4.2kg/cm festziehen.
11200 Kopfrad
W
21000 Rotor
X
Fig. 8.39
GRUNDIG Service 5 - 13
|
|
 |
> |
|