|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly what was needed to assess the product - excellent value and great service
;
A site where discontinualed schematic diagrams and back dated information can be found on discontinued radios tv's and any electronic equipment can be found. Newer manuals either Service and operating manuals. Radio amateurs should find this site a great source for ham radio equipment manuals. I will return to this site should I need information on any electrical equipment. priced easy to download in a PDF format and print pages need to undertake the repair.
;
Quality scan of the original. All the detail necessary to troubleshoot, repair and adjust the unit. I'm sure I will be downloading more manuals in the future as the need arises.
;
Exactly as described, a Service Manual complete with the schematics and PCB layout delivered in a timely manner. Many thanks for the great service.
 ;
some of the writing is a bit blur but the part in the schmatic was great and i have fixed the machine thanks
Abgleich / Adjustment Procedures
GV 5000 �, GV 5300 �
2.2 Family Board � Frontend (FV)
Test equipment: Oscilloscope with 10:1 Test Probe, Voltmeter, Colour Generator Service work after replacing the Tuner: Adjustments no. 2 Adjustment 1. Vision Demodulator Circuit, F5770 2. Delayed AGC Voltage, R3770 Preparation Feed in 38.9MHz / 100mVPP into the tuner output 1701-(17). Voltmeter: ..................................................... IC7772-(10) EE-mode. Feed in a PAL white test pattern with sound carrier (without sound modulation, UHF-range, Ch24, 67dBµV aerial signal) into the warmed-up VCR. Oscilloscope: ......................................... Tuner 1701-(17) EE-mode. Adjustment Procedure Set the voltage with F5770 (AFC) to 2.5V ±0.2V.
Set the amplitude with R3770 (AGC) to 550mVPP +0/-50mV.
2.3 Family Board � Video/Chroma (VS)
Test equipment: Oscilloscope with 10:1 Test Probe, Frequency Counter, Colour Generator Service work after replacing the Family Board: � Adjustment 1. Frequency Deviation Sync Value, R3054 2. Chroma Writing Current, R3038 Preparation AV recording (do not feed in an signal). Frequency counter: ............................................ 1911-(2) Connect IC7051-(2) to +5V. Oscilloscope: ...................................................... 1911-(2) Feed in a PAL red raster test pattern with 75% saturation (ratio burst: chroma = 1 : 2.2). AV recording. Adjustment Procedure Set frequency counter with R3054 (Sync. Frequ.) to 3.8MHz
±10kHz.
Set Chroma signal with R3038 (CHROMINANCE WRITING CURRENT PAL) to 71mVPP (-12.5dB of the FM-signal). Disconnect IC7051-(2) from +5V.
2.4 Family Board � Standard Sound / Audio Linear (AL)
Test equipment / aids: AF Millivoltmeter, AF Generator, Video Cassette of reputable brand. Service work after replacing the Family Board or the RP-Head: Adjustment no. 1.1, 2 Adjustment 1. Erase Frequency 70kHz, F5603 1.1 Bias (70kHz), R3618 1.2 Frequency Response Test Preparation Frequency counter: ............................................. 1918-(7) Record AF millivoltmeter: ................................................... R3600 Record. � Connect IC7601-(10) via 270� resistor to ground. � Feed in a CCVS signal via EURO-AV socket, contact 20. � Feed an audio signal of 200mVrms (480mVPP) from the AF generator to the EURO-AV socket, contact 2 or 6. � Make a recording of 400Hz and 8kHz each of 1 min at least. Afterwards play back these recordings. � Connect an AF millivoltmeter (oscilloscope) to EURO-AV socket, contact 1 or 3. AF generator (1kHz / 0.7Vrms): ..................................... EURO-AV socket, contact 2 or 6 AF millivoltmeter: ......... EURO-AV socket, contact 1 or 3 Record (Normal Play). Play back this recording. Adjustment Procedure With F5603 (BIAS Frequ.) set the reading on the frequency counter to 70kHz ±10kHz. Set the voltage drop across R3600 with R3618 15mVrms. Check the frequency response.
(BIAS)
to
The voltage ratio of 400Hz to 8kHz must not be higher than 1:0.7 or 0.7:1 (±3dB). If the voltage ratio exceeds these limits, the bias must be altered: To increase the playback voltage at 8kHz: Reduce "BIAS". To reduce the playback voltage at 8kHz: Increase "BIAS". Remove the 270� resistor between IC7601-(10) and ground. Set output voltage with R3606 (PB-Lev.) to 0.5Vrms ±50mV.
2. Playback Level, R3606
3. Keyboard Control Unit (ODCG1)
Test equipment: Frequency Counter Service work after replacing the Keyboard Control Unit: �
Adjustment 1. Clock, C2005
Preparation Disconnect from the mains. IC7101: ....... Connect Pins 67 and 68 with Pin 33 (+5V). Frequency Counter: ............................................ 1101-(1) Reconnect to the mains.
Adjustment Procedure The period is set with C2005 (CLOCK ADJ.) to 488.281,25ns ±0,715ns by the manufacturer. Disconnect IC7101-(67), -(68) from +5V (Pin 33).
3-4
GRUNDIG Service
|
|
|
> |
|
