|
Who's Online
There currently are 5905 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Great service. The manual was exactly what I was looking for: schematic + layout. I managed to fix the player. Highly recommended!
;
At $5,00 certainly good bang for your buck. Includes electric schematics as well as exploded parts view + parts list for reordering. Unfortunately no details on the PCB contents or working, but then again, this is not overly complex. Best bonus: this manual does contain the heavily searched for LED error codes as well as descriptions for test operation. Haven't gotten around to fixing the machine yet, one thing the manual won't do for you is getting it out of the kitchen assembly :-(
;
It`s not your fault tear down is rather incomplete. It doesn`t have complete instructions as to deconstruction for repair.
;
THANK YOU FOR A GOOD TRANSACTION, NICE COPY, CLEAR
;
Very Good! All the diagram are easy to read, and its complete.
HCD-EC70 SECTION 4 MECHANICAL ADJUSTMENTS
� Precaution 1. Clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head magnetizer close to the erase head.) 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, appiy suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. � Torque Measurement
Mode FWD FWD back tension FF Torque meter CQ-102AS Meter reading 2.0 � 8.0 mN � m (20 to 80 g � cm) (0.28 � 1.12 oz � inch) 0.15 � 0.6 mN � m (1.5 to 6 g � cm) (0.021 � 0.083 oz � inch) 5 � 17.7 mN � m (50 to 177 g � cm) (0.7 � 2.48 oz � inch) 5 � 17.7 mN � m (50 to 177 g � cm) (0.7 � 2.48 oz � inch)
SECTION 5 ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB=0.775 V
1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. � Test Tape
Tape P-4-A063 Signal 6.3 kHz, -10 dB Used for Azimuth Adjustment
RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT
Procedure: 1. Mode: Playback
test tape P-4-A063 (6.3 kHz, �10 dB) JACK board PHONES jack (J102) level meter set + �
CQ-102C
CQ-201AS
REW
CQ-201B
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
� Tape Tension Measurement
Mode FWD Tension Meter CQ-403A Meter Reading more than 80 g (more than 2.82 oz)
L-CH peak Output level
within 1dB within 1dB
Screw position
R-CH peak L-CH peak R-CH peak
Screw position
3. Mode: Playback
test tape P-4-A063 JACK board (6.3 kHz, �10 dB) PHONES jack oscilloscope (J102) V set H
waveform of oscilloscope
in phase 45° good
90° 135° 180° wrong
4. After the adjustments, apply suitable locking compound to the pats adjusted.
17
|
|
|
> |
|