|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Even if the PDF is a scan, I can read the information I need.
The price is affordable and the service (mail sending) is very fast.
Thanks ! Regards. William (Fan of Kenwood)
;
Very good quality original datasheet!I like this amazing website!!!!!!
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
HCD-GX20
[GC Test Mode] � All fluorecent segments and LEDs are tested. � Keyboard check. Procedure: 1. Press ?/1 button to turn the set ON. 2. To enter the test mode, press the three buttons x , GAME EQ and DISC 2 simultaneously. 3. All segments and LEDs (without STANDBY LED) are turned on. 4. Press GAME EQ and DISC 2 buttons simultaneously, and the key check mode is activated. 5. The message �KEY 0 0 0 0� is displayed. Each time a button is pressed, the key code number is displayed. 6. Press GAME EQ and DISC 2 buttons simultaneously, and the key count mode is activated. 7. The message �KEYCNT 0 1� is displayed. Each time a button is pressed, �KEYCNT 0 1� value increased. However, once a button is pressed, it is no longer taken into account. 8. Press GAME EQ and DISC 2 buttons simultaneously, and the head phone detect mode is activated. 9. The message �H_P OFF� is displayed when a headphone jack is not inserted. �H_P ON � is displayed when a headphone jack is inserted. 10. Press GAME EQ and DISC 2 buttons simultaneously, and the volume control detect mode is activated. 11. The message �VOLUME FLAT� is displayed. �VOLUME UP� is displayed if rotating VOLUME knob clockwise, or �VOLUME DOWN� is displayed if rotating counterclockwise. 12. To exit from the GC test mode after the volume control detect mode, press GAME EQ and DISC 2 buttons simultaneously. [Version and Destination Display Mode] � The version or destination is displayed. Procedure: 1. Press ?/1 button to turn the set ON. 2. To enter the test mode, press the three buttons x , GAME EQ and MOVIE EQ simultaneously. 3. The destination is displayed. 4. Press STOP and GROOVE buttons simultaneously. 5. The version is displayed. 6. To exit from this mode, press ?/1 button to turn the set OFF. [CD Service Mode] � This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pickup. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function �CD�. 3. To enter the test mode, press three buttons x , GAME EQ , and OPEN/CLOSE simultaneously. 4. The CD service mode is selected. 5. With the CD in stop status, press > button to move the pickup + to outside track, or press . button to inside track. � 6. To exit from this mode, perform as follows: 1) Move the pickup to the most inside track. 2) Press ?/1 button to turn the set OFF.
Note: � Always move the pickup to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded. � Do not run the sled motor excessively, otherwise the gear can be chipped.
[MC Test Mode] � This mode is used to test the function of the equalizer. Procedure: 1. Press ?/1 button to turn the set ON. 2. To enter the test mode, press the three buttons x , GAME EQ and DISC 3 simultaneously. 3. Press the MOVIE EQ button. The function of the equalizer is set to �MIN�. 4. Press the MUSIC EQ button. The function of the equalizer is set to �MAX�. 5. Press the P.FILE button. The function of the equalizer is set to �FLAT�. 6. To exit from this mode, press ?/1 button to turn the set OFF. [CD Ship Mode (No Memory Clear) ] � This mode moves the pickup to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function �CD�. 3. Press ?/1 button to turn the set OFF. 4. Press CD button and ?/1 button simultaneously. 5. The "STANDBY" display blinks instantaneously, and the CD ship mode is set.
16
|
|
|
> |
|
