|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
HCD-GX450
[PANEL Test Mode] � All fluorecent segments and LEDs are tested. � Keyboard check. Procedure: 1. Press ?/1 button to turn the set ON. 2. To enter the test mode, press the three buttons x , PLAY MODE/TUNING MODE and ENTER simultaneously. 3. All segments and LEDs (without STANDBY LED) are turned on. 4. Press X and ENTER buttons simultaneously, and the key check mode is activated. 5. The message �KEY 0 0 0 � is displayed. Each time a button is pressed, the key code number is displayed. 6. Press X and ENTER buttons simultaneously, and the key count mode is activated. 7. The message �KEYCNT 0� is displayed. Each time a button is pressed, �KEYCNT 0� value increased. However, once a button is pressed, it is no longer taken into account. 8. Press X and ENTER buttons simultaneously, and the head phone detect mode is activated. 9. The message �H_P OFF� is displayed when a headphone jack is not inserted. �H_P ON � is displayed when a headphone jack is inserted. 10. Press X and ENTER buttons simultaneously, and the volume control detect mode is activated. 11. The message �VOLUME FLAT� is displayed. �VOLUME UP� is displayed if rotating MASTER VOLUME knob clockwise, or �VOLUME DOWN� is displayed if rotating counterclockwise. 12. To exit from the GC test mode after the head phone detect mode, press X and ENTER buttons simultaneously. [Version and Destination Display Mode] � The version or destination is displayed. Procedure: 1. Press ?/1 button to turn the set ON. 2. To enter the test mode, press the three buttons x , PLAY MODE/TUNING MODE and DISC 2 simultaneously. 3. The destination is displayed. 4. Press DISPLAY buttons simultaneously. 5. The version is displayed. 6. To exit from this mode, press the three buttons x , PLAY MODE/TUNING MODE and DISC 2 simultaneously and press ?/1 button to turn the set OFF. [CD Service Mode] � This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function �CD�. 3. To enter the test mode, press three buttons x , PLAY MODE/ TUNING MODE , and Z simultaneously. 4. The CD service mode is selected. 5. With the CD in stop status, press M button to move the pick-up to outside track, or press m button to inside track. 6. To exit from this mode, perform as follows: 1) Move the pick-up to the most inside track. 2) Press ?/1 button to turn the set OFF.
Note: � Always move the pick-up to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded. � Do not run the sled motor excessively, otherwise the gear can be chipped.
[MC Test Mode] � This mode is used to test the function of the equalizer. Procedure: 1. Press ?/1 button to turn the set ON. 2. To enter the test mode, press the three buttons x , PLAY MODE/TUNING MODE and DISC 3 simultaneously. 3. Press the EQ + button. The function of the equalizer is set to �MAX�. 4. Press the EQ - button. The function of the equalizer is set to �MIN�. 5. Press the PRESET EQ button. The function of the equalizer is set to �EQ FLAT�. 6. MASTER VOLUME up and down. �VOLUME MIN� �VOLUME 16� �VOLUME MAX� is displayed. 7. Press the GROOVE button. The message �VACS OFF� or �VACS ON� is displayed. 8. To exit from this mode, press ?/1 button to turn the set OFF. [CD Ship Mode (LOCK) ] � This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function �CD�. 3. Press ?/1 button to turn the set OFF. 4. Press CD button and ?/1 button simultaneously. 5. The �STANDBY� display blinks instantaneously, the message �LOCK� is displayed and the CD ship mode is set. [CD Ship (LOCK) & COLD RESET MODE] Procedure: 1. Press ?/1 button to turn the set ON. 2. Select the function �CD�. 3. Press ?/1 button to turn the set OFF. 4. Press three buttons x , CD and DISPLAY simultaneously. 5. The �STANDBY� display blinks instantaneously and CD ship mode is set. 6. To fluorescent indicator tube displays �COLD RESET� and the set is reset. [Disc Tray Lock] Procedure: 1. Press the ?/1 button to turn the set ON. 2. Select the function �CD�. 3. Press two buttons of x and Z simultaneously for five seconds. 4. The message �LOCKED� is displayed and the tray is locked. (Even if exiting from this mode, the tray is still locked.) 5. Press two buttons of x and Z simultaneously for five seconds again. 6. The message �UNLOCKED� is displayed and the tray is unlocked. 7. To exit from this mode, press the ?/1 button to turn the set OFF.
14
|
|
|
> |
|
