HOT SHOT ABi FEATURES AND FUNCTIONS
1
2
3
4
www.radialeng.com
True to the Music
PAD (INPUT-A) inserts a -15dB PAD to lower the level of INPUT-A. PAD (INPUT-B) inserts a -15dB PAD to lower the level of INPUT-B. TRIM (INPUT-B) selects a -6dB reduction in level. Used to match the level of INPUT-A. LIFT disconnects the ground on pin-1 of INPUT-B XLR. Used to reduces buzz and hum caused by ground loops. TOGGLE heavy-duty latching footswitch selects between INPUT-A and INPUT-B. OUTPUT XLR sends a balanced signal to microphone snakes and mixing consoles. Rugged glass-filled nylon connector is 100% isolated from the chassis. INPUT-B XLR receives balanced signals from a microphone or other audio source. Rugged glass-filled nylon connector is 100% isolated from the chassis. INPUT-A XLR receives balanced signals from a microphone or other audio source. Rugged glass-filled nylon connector is 100% isolated from the chassis.
IMPORTANT NOTICE!
The Radial Hot Shot ABo & ABi are not intended for use with condenser microphones or active direct boxes that use phantom power. Phantom power puts voltage across the pins of the XLR jack that will create a loud transient when the Hot Shot is switched. Depending on your sound system the transient could be of significant level to damage loudspeakers. Before you start, it is important you know if phantom power is present and how to test your Hot Shot after connecting. Information in this manual will guide you how to safely use the Hot Shot ABo and ABi switchers. You are responsible to ensure safe and proper use. Using the ABo & ABi confirms you have taken full responsibility. If you are not 100% sure of your actions, please consult a qualified technician for advice.
Hot Shot ABi and ABo Owner�s Manual
5
6
7
8
Hot Shot ABo Order # R800 1509
1
2
3
4
RADIAL LIMITED THREE YEAR TRANSFERABLE WARRANTY
Radial Engineering Ltd. warrants this product to be free from defects in material and workmanship to the original owner and will remedy any such defects free of charge according to the terms of this warranty. Radial Engineering will repair or replace at its option any defective component(s) of this product, excluding the finish, the footswitch (footswitch is warranted for 90 days) and wear and tear from normal use, for a period of three (3) years from the original date of purchase. In the event that a particular product is no longer available, Radial Engineering reserves the right to replace the product with a similar product of equal or greater value. To make a request or claim under this limited warranty, the product must be returned prepaid in the original shipping container (or equivalent) to Radial Engineering or to an authorized repair centre and you must assume the risk of loss or damage. A copy of the original invoice showing date of purchase and the dealer name must accompany any request for work to be performed under this limited warranty. This limited warranty shall not apply if the product has been damaged due to abuse, misuse, misapplication, accident or as a result of service or modification by any other than an authorized repair centre.
8
Hot Shot ABi Order # R800 1508
5
6
7
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND DESCRIBED ABOVE. NO WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF THREE YEARS. RADIAL ENGINEERING LTD. SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU LIVE.
CAUTION: PLEASE READ THE IMPORTANT NOTICE ON THE BACK COVER
Radial Engineering Ltd. 1638 Kebet Way, Port Coquitlam BC V3C 5W9 Tel: 604-942-1001 Fax: 604-942-1010 email:
[email protected]
Radial Hot Shot ABi and ABo users guide V1.0 - Part #: R870 1170 00 Subject to change without notice
Radial Engineering
Hot Shot ABo & ABi User Guide
Radial Engineering
Hot Shot ABo & ABi User Guide
