|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
;
It was just what I need to fix my old BMW's CD player. Very convenient also. Thank you.
;
Great Manual! It contains all the wiring schematics and mechanical exploded views that are essential for service and repair. I was surprised I even found this for such an old machine. Only wish I knew of this site many years ago.
;
Great manual very clear copied. You are making an incredible job. I appreciate a lot the rapidity and your efficiency. Thanks a lot
2.3.2 Checking/Adjustment of the Height and Tilt of the Audio Control Head Note: Set a temporary level of the height of the A/C head in advance to make the adjustment easier after the A/C head has been replaced. (See Fig.22-15.) (1) Connect CH-1 of the oscilloscope to AUDIO OUT and CH2 to TP4001 (CTL.P) of the main board assembly and observe the waveforms on both channels in the ALT mode. (2) Play the alignment tape MHPE and adjust it by turning the screws (1), (2) and (3) little by little until the waveform of both the audio output signal and the control pulse reach maximum. The screw (1) and screw (3) are for adjustment of tilt and screw (2) for azimuth.
(6) Then play the alignment tape MHPE-L. (7) Press the channel buttons (+, �) simultaneously during playback to enter the manual tracking mode. (This also brings the tracking to the centre.) (8) Perform the tracking operation and make sure that the FM waveform is at its maximum. (9) If it is not at maximum, loosen the temporarily tightened the screw (4) and turn the A/C head position bit to bring the audio control head to a position, around where the waveform reaches its maximum for the first time. Then tighten the screws (4) and (5).
Toward the capstan Toward the drum
Head base
Head base A/C head position bit PTU94010
Waveform output
Screw (4)
(2)
(1)
To the drum
(3) Audio control head
Screw (5) Audio control head To the capstan
Audio out
Fig. 2-3-6
TP4001 (CTL. P)
Fig. 2-3-5
MHPE played with the standard-width head
MHPE-L played with the triple-width head
2.3.3 Checking/Adjustment of the Audio Control Head Phase (X-Value) (1) Connect the oscilloscope to TP106(PB.FM) of the main board assembly and to TP111(D.FF) of the main board assembly for external sync connection. (2) Play the alignment tape MHPE and observe the FM waveforms. (3) Press the channel buttons (+, �) simultaneously during playback to enter the manual tracking mode. (This also brings tracking to the centre.) (4) Loosen screws (4) and (5) so that the A/C head position bit (PTU94010) is set as indicated in Fig.2-3-6. (5) Turn the A/C head position bit fully toward the capstan. Then turn it back gradually toward the drum and stop on the second peak point position of the FM waveform output level. Then tighten the screw (4) temporarily.
X-value adjustment point To the drum Control head position To the capstan
Maximize
Fig. 2-3-7
2-22
|
|
|
> |
|
