|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I needed the manual immediately and I got it immediately. I couldn't find this manual anywhere else on the net. The site was easy to traverse, and the price was very reasonable. I'll definitely be back for any future needs.
 ;
I received a good service manual, with good resolution. Improve the instructions for the purchase because they are not well understood.
For the rest, so good.
Thanks Angel.
;
Very good documentation for the Grundig 2077 model (as well as similar 800/900/1000 series radios). The first two pages are a summary of reception specifications and output capability. The third page is the tuner dial indicator and dial cord routing diagram. the final ~5 pages are the schematics for the various models (including 2077). The scan quality of the schematics are good, adn can be easily read if zoomed in. The documents are in German, not English as stated. It would have been nice to have the tuning sequence and settings, and some trouble shooting materials... or component and wiring map.
;
Perfect like it was descriped, Perfect like it was descriped
;
Very good detail, all pages clear, exactly what I needed
4.2 Mechanism compatibility adjustment Note: � Although compatibility adjustment is very important, it is not necessary to perform this as part of the normal servicing work. It will be required when you have replaced the A/C head, drum assembly or any part of the tape transport system. � To prevent damaging the alignment tape in the compatibility adjustment, prepare a cassette tape (for self-recording/playback), perform a test on it by transporting it and making sure that the tape is not bent by the tape transport mechanisms such as in the guide rollers.(See Fig.4-2b.) 4.2.1 Tension pole position Note: � This adjustment must be performed every time the tension band is replaced.
Signal Mode (A) � Back tension cassette gauge [PUJ48076-2] (B1) � PB (B2) � Eject end � Adjust pin [Mechansim assembly]
4.2.2 FM waveform linearity
Signal (A1) � Alignment tape(SP, stairstep, PAL) [MHPE] (A2) � Alignment tape(LP, stairstep, PAL) [MHPE-L] (UA Model) (A1) � Alignment tape(SP, stairstep, PAL) [MHP] (A2) � Alignment tape(EP, stairstep, PAL) [MHP-L] (UB, UM Model) (B) � PB (C) � Oscilloscope (D) � TP106 (PB. FM) (E) � TP111 (D. FF) (F) � Guide roller [Mechanism assembly] (G) � Flat V. PB FM waveform (H) � Roller driver [PTU94002]
Mode Equipment Measuring point External trigger Adjustment part Specified value Adjustment tool
(1) Play back the alignment tape (A1). (2) Apply the external trigger signal to D.FF (E), to observe the V.PB FM waveform at the measuring point (D). (3) Set the VCR to the manual tracking mode. (4) Make sure that there is no significant level drop of the V.PB FM waveform caused by the tracking operation, with its generally parallel and linear variation ensured. Perform the following adjustments when required. (See Fig. 4-2c.) (5) Reduce the V.PB FM waveform by the tracking operation. If a drop in level is found on the left side, turn the guide roller of the pole base assembly (supply side) with the roller driver to make the V.PB FM waveform linear. If a drop in level is on the right side, likewise turn the guide roller of the pole base assembly (take-up side) with the roller driver to make it linear. (See Fig. 4-2c.) (6) Make sure that the V.PB FM waveform varies in parallel and linearly with the tracking operation again. When required, perform fine-adjustment of the guide roller of the pole base assembly (supply or take-up side). (7) Unload the cassette tape once, play back the alignment tape (A1) again and confirm the V.PB FM waveform. (8) After adjustment, confirm that the tape wrinkling does not occur at the roller upper or lower limits. (See Fig. 4-2b.) [Perform adjustment step (9) only for the models equipped with SP mode and EP (or LP) mode.] [Perform adjustment step (9) only for the models equipped with SP mode and EP (or LP) mode.] (9) Repeat steps (1) to (8) by using the alignment tape (A2).
Improper Proper
Adjustment part (F) Specified value (G)
� 25 - 51 gf·cm (2.45 - 5 x 10-3 Nm)
(1) Play back the back tension cassette gauge (A). (2) Check that the indicated value on the left side gauge is within the specified value (G). (3) If the indicated value is not within the specified value (G), perform the adjustment in a following procedure.(See Fig.4-2a.) a) Remove the top frame, cassette holder and side frames (L/R) all together. (Refer to the SERVICE MANUAL No.86700 [MECHANISM ASSEMBLY].) b) Rotate the loading motor gear to move the control plate so that the triangular stamping to the left of the "P"stamping is aligned with the stamping (a) on the main deck. This positioning is mode (B1). c) Adjust by turning the adjustment pin so that the tip of the tension arm is aligned with the stamping (b) on the main deck. d) Rotate the reel disk (S) by about one turn clockwise and make sure that the round hole of the adjustment pin is located in the "OK" range. If it is outside this range, restart the adjustment from the beginning. After completion of the adjustment, rotate the loading gear motor to return it to the mode (B2) position.
TENSION ARM
(a) GUIDE ROLLER
CONTROL PLATE Stamping(a)
Stamping(b) OK
(b) GUIDE POLE
Fig.4-2b
NG
ADJUST PIN
Fig.4-2a
(No.YD007)1-11
|
|
|
> |
|
