|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
;
The manual was exactly what I wanted and I found it nowhere else. Thanks!
;
Having purchased a 1994 Kenwood music system from a Charity shop in 2013 (it was a high end product in its day), I found myself not quite knowing where to plug in what, and how to do this, that and the next thing. I needed a Manual, and after failure with another online 'Manual provider' I found Owner Manuals dot com. Well, I wasn't sure, but it was only $5, and if things didn't work out, I wouldn't have lost much...
But things DID work out. After paying my childrens inheritance money, $4.99, I was sent a Manual for my Kenwood System very quickly. Alas, it was in German, and being Scottish, I could not read it or get my system in order from it...a rapid email to them brought the English Manual in short order, and my retro-system was and IS up and running in it's regulation settings.
I am very grateful to http://www.owner-manuals.com for their quick service and for even having such an obsolete Manual in the first place! If you need a Manual for ANYTHING, try here first. I wouldn't be surprised if I bought a 1928 Marconi radio, and got the user Manual for THAT here too!
Top marks.
John Copeland
Glasgow
Scotland
;
I was so happy that the owner's manual was available. It is well written and helped me to use the radio/CD player/recorder without problems. Thanks for making it available.
Irene Lambert
;
Excellant!!! Very quick and easy....Best $4.99 I have spent in a very long time..
I highly recommend this.
EN
RECORDING
SYMPTOM
1. Recording cannot be started.
59
POSSIBLE CAUSE
� There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed. � "L-1", "F-1", "S-1" or "S-2" has been selected as the input mode. � The source (another video recorder, camcorder) has not been properly connected. � All necessary power switches have not been turned on. � The input mode is not correct. � The camcorder has not been properly connected. � The input mode is not correct.
CORRECTIVE ACTION
Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed. Set to the desired channel. Confirm that the source is properly connected. Confirm that all units' power switches are turned on. Set the input mode to "L-1", "F-1", "S1" or "S-2". Confirm that the camcorder is properly connected. Set the input mode to "L-1", "F-1", "S1" or "S-2".
2. TV broadcasts cannot be recorded. 3. Tape-to-tape editing is not possible.
4. Camcorder recording is not possible.
TIMER RECORDING
SYMPTOM
1. Timer recording won't work.
POSSIBLE CAUSE
� The clock and/or the timer have been set incorrectly. � The timer is not engaged. � Timer recording is in progress.
CORRECTIVE ACTION
Re-perform the clock and/or timer settings. Press � and confirm that "�" is displayed on the display panel. Timer programming can't be performed while a timer recording is in progress. Wait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact. Check the programmed data and reprogram as necessary, then press � again. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. Refer to "G-CODE/SHOWVIEW System Setup" and re-perform the procedure. ( pg. 26)
2. On-screen timer programming is not possible. 3. "�" and "]" on the display panel won't stop blinking.
� The timer is engaged but there's no cassette loaded. � The loaded cassette has had its Record Safety tab removed.
4. "�" blinks for 10 seconds and the Timer mode is disengaged.
� � has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. � The end of the tape was reached during timer recording.
5. The power shuts off and "�" and "]" won't stop blinking.
6. The G-CODE/SHOWVIEW system does not timer-record properly.
� The recorder's channel positions have been set incorrectly.
|
|
|
> |
|
