|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was having a hard time finding the problem with this Mackie 1604 unit. I didn't have a schematic. Went looking on the web and found your site and the price was more then reasonable. Ordered it and within the hour had the manual and within 15 minutes had the unit fixed. Best $4.99 I ever spent. Thank you.
Doug
;
This is a service manual in every sense of the word ( French and German versions of the text are included, as well as English..)
There are explanations of the mechanical and electrical functions, plenty of mechanical drawings, and the needed schematics. The quality of the scanning is excellent - all the component values are clearly legible - and very usefully there are pcb component layouts, so you can find a component on the schematic, and then very quicky pinpoint its physical location on the relevant pcb.
I cannot see how I can give this manual any less than the maximum 5 stars! Great value for money, which will pay for itself immediately. Excellent all round!
;
the manual is great and especially hard to find... thanks for the great service and having a hard to find manuel_
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.50 of store credit for Your review.
;
hat alles sehr gut geklappt. Das Servicemaual ist gut zu verwenden. Die Pläne und Schrift
ist klar und leserlich. Außerdem preiswert. Grüße an alle Hifi-Bastler
(Installation)
1. Install the SPACER shown in the Fig. 2-34-1. Note : Be sure to use the new SPACER packed with the new UPPER DRUM ASSY. 2. Install the UPPER DRUM ASSY shown in the Fig. 234-1. 3. Install the END RING so that the reference hole (A) of the END RING shown in the Fig. 2-34-2 will be placed in parallel with the Rear Line of the MAIN PLATE ASSY. (The reference hole (A) should be on the right when viewed from the bottom.) 4. Apply the screw-sealing agent to the hexagon screw (c) fastening the END RING shown in the Fig. 2-34-1. 5. Install the ROTOR CASE shown in the Fig. 2-34-3, matching its Holes with the three reference holes (B) of the UPPER DRUM ASSY. 6. Install the BRUSH shown in the Fig. 2-34-1. 7. Install the BRUSH SPRING shown in the Fig. 2-34-1. 8. Install the DRUM MOTOR STATOR shown in the Fig. 2-34-1. 9. Connect the LEAD CONNECTOR of the DRUM ASSY shown in the Fig. 2-34-1. 10. Perform the Item "PLAYBACK Switching Point" adjustment. 11. Perform the Item "Interchangeability Adjustment of the Mechanism". 12. Clean the DRUM ASSY with alcohol.
A END RING
Rear Line of MAIN PLATE ASSY
Fig. 2-34-2
ROTOR CASE
Fig. 2-34-3
B UPPER DRUM ASSY
Lock
2-35.CAPSTAN MOTOR
SET POSITION : Normal Remove the following part before replacing the CAPSTAN MOTOR. Refer to the corresponding item to install it. � REEL BELT (Item 2-14.)
Lock STAY PLATE WORM WHEEL
(Removal)
1. Rotate the WORM WHEEL in the Fig. 2-35-1 in the direction shown by the arrow A to release the Hooks of the BOTTOM ASSY from the Locks of the STAY PLATE. 2. Rotate the WORM WHEEL in the Fig. 2-35-2 in the direction shown by the arrow A so that the GUIDE ARM (TU) moves in the direction of arrow B and expose the three screws (a) fastening the CAPSTAN MOTOR. 3. Remove the three screws (a) fastening the CAPSTAN MOTOR shown in the Fig. 2-35-2 to remove the CAPSTAN MOTOR.
A
Hook of BOTTOM ASSY
Fig. 2-35-1
- 27 -
|
|
|
> |
|
