|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
 ;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
;
This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
;
Fast and courteous service. Product delivered as described. Thank you.
Surround sound settings
07
Chapter 7
Surround sound settings
5
Using the Setup menu
From the Setup menu you can access all the surround sound settings of the system1, including channel levels, speaker distances, dynamic range adjustment and dual mono audio playback. Use the following buttons to use the Setup menu.
Press ENTER when you�re finished. � If you use the Auto MCACC feature again, it will overwrite the settings you have made here.
Speaker distance setting
The Auto MCACC feature (see page 15) should give you the best surround sound setup. However you may find that by further adjustment of the speaker distance settings you can improve the surround sound in your listening room. Set the distance of each speaker from your normal listening position.
SLEEP
ENTER
SETUP
CLEAR
SR
TUNE ST ST
1
TEST TONE
Press SETUP.
ENTER
SOUND TUNE
SOUND RETRIEVER
2 Use the / (cursor left/right) buttons to select DISTANCE, then press ENTER. Use / (cursor left/right) to select a speaker; (cursor up/down) to adjust the distance. Adjust the following speakers:
� L � Front left speaker � C � Center speaker � R � Front right speaker � SR � Surround right speaker � SL � Surround left speaker � SW � Subwoofer Each speaker can be adjusted from 0.3 m to 9.0 m.
3
/
SURROUND
ADVANCED
F.S.SURR
MCACC
Channel level setting
The Auto MCACC feature (see page 15) should give you the best surround sound setup. However you may find that by further adjustment of the channel levels you can improve the surround sound in your listening room. This method of setting the channel levels allows you to listen to a source and adjust the levels of each playback channel. Note that the channel level settings for stereo playback are independent of the settings for surround sound playback. A further method of setting the channel levels is to use the test tone method. See Adjusting the channel levels using the test tone on page 22 for more on this.
4
Press ENTER when you�re finished. � If you use the Auto MCACC feature again, it will overwrite the settings you have made here.
Dynamic Range Control
When watching Dolby Digital or DTS material at low volume, low level sounds � including some of the dialogue � can be difficult to hear properly. Using one of the Dynamic Range Control (DRC) settings can help by bringing up the low level sounds, while controlling high level peaks. Dynamic Range Control works only with Dolby Digital soundtracks and some DTS soundtracks.
English
1 2
Select stereo or multichannel playback for a source. Press SETUP.
3 Use the / (cursor left/right) buttons to select CH LEVEL, then press ENTER. 4 Use / (cursor left/right) to select a channel; / (cursor up/down) to adjust the level of that channel. � You can adjust the level of each channel by ±10 dB.
� If the system is in Stereo or Virtual mode, or a stereo source is playing in Auto mode, you will not be able to adjust the center or surround channels.
1 Press SETUP. 2 Use the / (cursor left/right) buttons to select DRC, then press ENTER.
Note 1 There are other settings you can adjust from the Setup menu; these are explained in Listening to the radio on page 19 and Additional information on page 26.
21
En
|
|
|
> |
|
