|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
More than pleased with my prurchase, very good product for the price.
;
Manual-link came 30 minutes after having paid for an extremely rare (40 years old) item (sony icr-120) and helped me to get the radio rework again. So really good help for me, fast and reliable delivery and -taken that into consideration- a very reasonable price for that service. So thanks again! Mike, Germany
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
ICD-ST10/ST20 SECTION 3 TEST MODE
[Setting Method of the Test Mode] To enter the test mode, turn on the HOLD . switch while pressing the x key and VOL+ key at the same time with the power on. [Operation in the Test Mode] After entering the test mode, you can move within the test menu by pressing the . / > key. You can move to the submenu by pressing the x�B key. Then each test mode can be executed. 1. LCD test � LCD is tested of all light-on and all light-off.
xB
ALL
[Exiting Method of the Test Mode] Exit the test mode by turning off the power. [Initial Status of the Test Mode] When the test mode is set, the LCD display appears as shown below. LCD display (Example)
. > (select), x B (set)
LCD
LCD
x
:
OFF LCD CHK LCD ALL LCD
(LCD off)
CHK
ABCDE mM L
H
:
START
STSPLP
AB
5A 102
01
ST20
Iris(DSP) version : 5A SakuraR(CPU) version : 1.02 (In α version or β version, A or B is displayed) LPEC ST version : 01 Model code : ST20
� � �
88 REC 888
YM MM DS
.>
CHK
888888
END
5A102 01ST20
x
x
x
[Flow Chart of the Test Mode]
START TEST MODE
2. Audio test Perform the through-playback and sine wave output. � Contents of the submenu DSP ST: DSP STEREO through mode DSP MO: DSP MONO through mode SIN: 1 kHz sine wave output mode � Select the microphone sensitivity with the A-B switch. HtMtLtHtMt ... � The VOR detection operation can be checked by the LED. Sound: The red LED is turned on. No sound: The red LED is turned off.
RST
. > . LCD . AU IO . SLEEP . BEEP . RTC . > > KEY .
Turn off the power (Extract the batteries or DC jack)
Initial status of test mode Model code, LPEC ST, F/W version display
> MENU > > .
KEY
COUNT > > . USB . LED . BATT
>
>
>
>
� MUTE can be set to �ON� or �OFF� with the ERASE key. � The sound volume can be adjusted with the VOL+ key or VOL- key during the audio test except the MUTE mode. � In the directional microphone selection, ON/OFF of the DIRECTNL switch is performed with the DIVIDE key. DIRECTNL switch ON : The green LED is turned on. OFF : The green LED is turned off. � In the audio test mode the operation is performed according to JACK detection. � The microphone sensitivity, sound volume and MUTE (on/off) are displayed on the LCD. � The microphone sensitivity selection and the VOR test are effective in the through-playback mode. � The directional microphone selection is effective in the DSP MONO through mode.
DSP STEREO through mode / MIC : M / MUTE : ON / VOL-LEVEL : 12 t "M / on / 12 / DSP ST" DSP MONO through mode / MIC : H / MUTE : OFF / VOL-LEVEL : 23 t "H / oF / 23 / DSP MO" 1k sine wave output mode / MUTE : ON / VOL-LEVEL : 06 t "on / 06 / SIN"
END TEST MODE
xB
AU IO
. > (select), x B (set)
DSP ST
x
:
DSP MO SIN DSP ST
H
mM
m
:
on 12 DSP ST
oF 23 DSP MO
on 06 SIN
x
x
x
8
|
|
|
> |
|
