|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Il service manual molto accurato. Rapidi nella risposta
;
Quick site processing. A complete and very useful manual with all details. Thank you!
;
Quick service response. A useful and very rare service manual with all details. I recomend this service.
;
I ordered this manual sometime in the afternoon and I received it on my e-mail the same evening.
This is a fantastically good and properly scanned copy of the original manual. All pages are of the same scale and they overlap each other. It means that you can print the manual and easily make it as a convenient paper manual.
The content of the manual is fantastic. Alignment descriptions, PCB layouts and elementary diagrams are explicit and precise. I immediately found what I was looking for. Thanks to this manual and Owner-Manuals.com my amplifier is alive again. Many thanx indded!
;
The manual was well-scanned and easy to read. As an added bonus, the Operator's Manual was bundled with the Service Manual!
I'd definitely use owner-manuals.com again.
ICD-ST10/ST20 SECTION 3 TEST MODE
[Setting Method of the Test Mode] To enter the test mode, turn on the HOLD . switch while pressing the x key and VOL+ key at the same time with the power on. [Operation in the Test Mode] After entering the test mode, you can move within the test menu by pressing the . / > key. You can move to the submenu by pressing the x�B key. Then each test mode can be executed. 1. LCD test � LCD is tested of all light-on and all light-off.
xB
ALL
[Exiting Method of the Test Mode] Exit the test mode by turning off the power. [Initial Status of the Test Mode] When the test mode is set, the LCD display appears as shown below. LCD display (Example)
. > (select), x B (set)
LCD
LCD
x
:
OFF LCD CHK LCD ALL LCD
(LCD off)
CHK
ABCDE mM L
H
:
START
STSPLP
AB
5A 102
01
ST20
Iris(DSP) version : 5A SakuraR(CPU) version : 1.02 (In α version or β version, A or B is displayed) LPEC ST version : 01 Model code : ST20
� � �
88 REC 888
YM MM DS
.>
CHK
888888
END
5A102 01ST20
x
x
x
[Flow Chart of the Test Mode]
START TEST MODE
2. Audio test Perform the through-playback and sine wave output. � Contents of the submenu DSP ST: DSP STEREO through mode DSP MO: DSP MONO through mode SIN: 1 kHz sine wave output mode � Select the microphone sensitivity with the A-B switch. HtMtLtHtMt ... � The VOR detection operation can be checked by the LED. Sound: The red LED is turned on. No sound: The red LED is turned off.
RST
. > . LCD . AU IO . SLEEP . BEEP . RTC . > > KEY .
Turn off the power (Extract the batteries or DC jack)
Initial status of test mode Model code, LPEC ST, F/W version display
> MENU > > .
KEY
COUNT > > . USB . LED . BATT
>
>
>
>
� MUTE can be set to �ON� or �OFF� with the ERASE key. � The sound volume can be adjusted with the VOL+ key or VOL- key during the audio test except the MUTE mode. � In the directional microphone selection, ON/OFF of the DIRECTNL switch is performed with the DIVIDE key. DIRECTNL switch ON : The green LED is turned on. OFF : The green LED is turned off. � In the audio test mode the operation is performed according to JACK detection. � The microphone sensitivity, sound volume and MUTE (on/off) are displayed on the LCD. � The microphone sensitivity selection and the VOR test are effective in the through-playback mode. � The directional microphone selection is effective in the DSP MONO through mode.
DSP STEREO through mode / MIC : M / MUTE : ON / VOL-LEVEL : 12 t "M / on / 12 / DSP ST" DSP MONO through mode / MIC : H / MUTE : OFF / VOL-LEVEL : 23 t "H / oF / 23 / DSP MO" 1k sine wave output mode / MUTE : ON / VOL-LEVEL : 06 t "on / 06 / SIN"
END TEST MODE
xB
AU IO
. > (select), x B (set)
DSP ST
x
:
DSP MO SIN DSP ST
H
mM
m
:
on 12 DSP ST
oF 23 DSP MO
on 06 SIN
x
x
x
8
|
|
|
> |
|
