|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent quality and quickly delivered manuals at a fair price. Great care is taken in the reproduction process. Even photographs and highly detailed drawings are as clear as in the original. That cannot be said for some freelance manual copies I have obtained from the web. If you have exhausted your internet search of technical manuals, try Owner-Manuals.com. If they do not have it, I do not think it exists. Perhaps, if requested, they may be able to find it. Their resources are certainly greater than most. Shopping here certainly beats waiting for months or years for the manual you seek to appear in an internet auction or garage sale.
;
Very detailed product, also it is a scanning from original, very useful if you have to service this type of amplifier ! Very good product, very hard to find!
;
the Manual was made available as promised, the scans were excellent..Good Work !!!
;
It's complete and helpful manual with good quality of scan. Thanks very much.
;
The service was quick and simple, finding the service manual easy and it appears to be the original with colour schematics. It contained the info I was after and so sorted the problem.
I have copied it to CD and attached the envelope to the inside back cover of the owners manual. Good manual and excelent service. Robin Wood, Wood Electronics, New Zealand.
SECTION 2 DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
SECTION 3 ELECTRICAL ADJUSTMENTS
0 dB = 1µV
[FM] Setting: Band switch: FM
FM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. L3 86.5 MHz (64.0MHz) CT3 109.5 MHz
CABINET (REAR) ASSY
9 telescopic antenna 1 claw 3 lid, battery case
FM RF signal generator 0.01 µF
FM antenna terminal 4� set
level meter + �
FM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L2 CT2 86.5 MHz (64.0MHz) 109.5 MHz
!¡ INLET board 5 claw !º two screws (P3 � 10) 2 two claws
22.5 kHz frequency deviation by 400 Hz signal Output level: as low as possible
speaker terminal
AM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. L4 520 kHz 1,750 kHz
[AM] Setting: Band switch: AM
AM RF signal generator Put the lead-wire antenna close to the set. 4� set 30% amplitude speaker terminal modulation by 400 Hz signal Output level: as low as possible + � level meter
CT4
4 six screws (BTP3 � 14) 7 screw (P2.6 � 8)
AM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L1 CT1 AM IF ADJUSTMENT Adjust for a maximum reading on level meter. T1 455 kHz 600 kHz 1,400 kHz
8 lug, 3 6 cabinet (rear) assy
� Repeat the procedures in each adjustment several times, and the frequency coverage and tracking adjustments should be finally done by the trimmer capacitors. � Remove FM antenna in FM adjustments. Adjustment Location: [MAIN board] (Component Side)
FM Antenna in AM Tracking Adjustment L1 CT1
(
): East European model
FM Tracking Adjustment L2 CT2
POINTER SETTING
4 chassis 3 two claws
L4 T1 AM IF Adjustment CT4 CT3 L3 IC1 Speaker in
AM Frequency Coverage Adjustment FM Frequency Coverage Adjustment
5 Mount the pointer
2 knob (TUNE)
3 claw
1 Turn CV1 fully in the arrow direction.
T2
6 Insert the pointer to the knob (TUNE) fitting the concave position of the pointer to the convex position of the knob (TUNE).
�3�
�4�
|
|
|
> |
|
