|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual is complete with excellent quality! One suggestion, show number of pages and weather it is multi-lingual. The AD 600 Manuel is about 76 pages and over half is non English. This results in a larger print job than usually needed. Having this information, one could select the desired pages for printing.
 ;
I've been looking for a copy of the original user/owner manual. Just what the doctor ordered, thank you.
;
the manual was very helpful thank you very much no one else was able to help me thanx
;
This is an excellent handbook. We had no information on the appliance until we obtained this and are now able to use the appliance to its full potential. Strongly recommended.
;
Very happy to find this from owners-manual.com and the enclosed spec sheet as well.
Not longer available from Sony.
Model ILP-1 User Guide
Output Clipping Level LOAD 150 � 800 � GAIN SWITCH 0 0.0 dBV �13.0 dBV +10 �7.0 dBV �21.0 dBV
Electromagnetic Hum Sensitivity �146 dBV equivalent in 1 millioersted field Electrostatic Hum Pickup �97 dBV typical, measured in 12 kV field Polarity Positive voltage on pin 3 relative to pin 1 of the input connector produces positive voltage on pin 2 relative to pin 3 of the output connector Power Requirement Phantom power: 11 to 52 Vdc at pins 2 and 3 relative to pin 1 Dimensions See Figure 1.
138 mm (5 7/16 IN.)
GENERAL The ILP-1 is a high-clipping level, low-noise preamplifier designed exclusively for use with Shure Models SM90A, SM91A, SM98A, SM102B and SM102W, or for use as a replacement preamplifier for older Models SM90, SM91, and SM98. The ILP-1 connects to balanced microphone inputs providing 11 to 52 Vdc phantom power. Two switches on the ILP-1 allow you to set low-frequency response (flat or rolloff at 12 dB/octave) and gain (0 or +10 dB). The low cut switch minimizes ambient low-frequency noise from sources such as heating or air conditioner fans. The supplied mounting clamps hold the preamplifier in place for permanent installations. Use either one or two clamps depending on location and application. SPECIFICATIONS Frequency Response
Switch Setting Flat Rolloff Gain (dB) 30 Hz to 20 kHz (6 dB/octave rolloff below 30 Hz) 80 Hz to 20 kHz (12 dB/octave rolloff below 80 Hz) Gain (dB) �6.0 (±0.5 dB) +4.0 (+1.0, �1.5 dB)
20 mm (13/16 IN.)
DIMENSIONS FIGURE 1 Weight 170 grams (6.0 ounces) Connectors 3-pin male (TB3M) Input: mini Output: 3-pin (male) XLR-type Switches Two recessed slide switches (low frequency rolloff and 0/+10 gain) Case Steel, matte black enamel finished Environmental Conditions Operating Temperature: �19 to 57° C (�20 to 13° F) Storage Temperature: �29 to 74° C (�20 to 168° F) Relative Humidity: 0 to 95%
Gain (at 1 kHz, no load)
Switch Setting 0 +10
Output Impedance Rated at 150 � (90 � actual) Output Noise (V , grounded, no load)
in
�123 dBV rms typical, A-weighted
E2002, Shure Incorporated 27A8494 (Rev. 1)
Printed in U.S.A.
|
|
|
> |
|
