|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
 ;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
;
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
English 19. Thermal protection
A thermal sensor in the body of the iWASH 575 EB protects the unit against overheating. The thermal sensor removes power from the lamp should the ambient temperature exceed the set maximum or if there is a lack of air flow or there is a fan malfunction.
20. Lamp circuit protection
Two timers operate simultaneously within the projector to protect the lamp ignitior and power supply against prolonged operation in non-ideal conditions. A protection device, inside the electronic ballast, impedes attempts to power up the lamp for more than 3 seconds if the lamp has failed to ignite. The device will automatically attempt to restart the lamp for a further 3 seconds in every minute. A software timer reattempts lamp ignition for a period of 20 seconds in every minute for up to 8 minutes; then it preserves the lamp circuit by not allowing high voltage to the lamp (assuming the lamp to have passed its useful life). The display will show
LAER (lamp circuit error) each time an unsuccessful attempt is made to turn on the lamp
NOTE: it is important to remove power from the fixture if the lamp has reached the end of its life and to replace the lamp.
21. Maintenance
Whilst every possible precaution has been taken to ensure the trouble-free operation of your IWASH 575 EB, the following periodic maintenance is highly recommended. All maintenance should be effected with the power to the unit switched off
Attention
Disconnect mains power prior to removing the projector housing. To gain access to the internals of the unit refer to section 17. Opening up the projector.
periodic cleaning lenses and reflectors
Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks; the period for this periodic cleaning will depend, of course, upon the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor.
periodic maintenance lamp
The lamp should be replaced if there is any observable damage or deformation due to heat. This will avoid the danger of the lamp exploding.
mechanicals
Periodically check all mechanical devices for wear and tear; gears, guides, belts, etc., replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your coemar distributor.
electrical components
Check all electrical components for correct earthing and proper attachment of all connectors, refastening if necessary.
fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the iWASH 575 EB. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.
|
|
|
> |
|
