|
|
|
Who's Online
There currently are 5939 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Everything is OK. Owner's Manual I downloaded ( I get link for it by email).
;
The only reason I gave this less than 4 stars, is because it shouldn't take 24 hrs to have the download available. I was surprised to find that I had to wait until the next day to be able to download the manual that I paid for.
The manual itself is the correct manual.
 ;
Excellent replacement for original Owner´s Manual. I am totally satisfied!
;
Great service. Manual is as advertised and delivered when promised.
;
Perfect quality, highly appreciated service !!!
Fast delivery of the download info, no issues at all. Recommended E-manual shop !!!
2 Installing the control board
1. Install the control board
Use the supplied two screw assy on the left side of the terminal board and install the control board.
Control boardn Terminal board
4 Installing the heater board
Install the heater after adjusting the field angle and lens of the camera.
1. Install the heater board to
the camera unit
Rotate the heater in the direction of the arrow such that the claw (B section) of the heater board is hooked on the notch (A section) of the camera unit.
CN4 terminal
1.
Heater board
2. Connect the CN4 cable
Connect the CN4 cable on the control board to the CN4 terminal on the terminal board. Meanwhile, bring the CN5 cable out of the base.
CN5 Cable
CAUTION
� Pay attention when installing the heater board to the camera unit as there is a correct direction. � The dome cover cannot be installed if the heater board is not installed securely. Connect the CN5 cable of the control
A section B section
Screw assy (attached)
CN4 cable
3
Before installing the heater board 2. Connect the cable
1.
Desiccant
2.
CN5 cable of control board
1. Put the desiccant inside
the base
Put the desiccant that comes with this unit inside the base and secure with a lug plate.
board to the CN5 cable of the heater board. Once the CN5 cables are connected, insert them between the base and camera unit.
Memo:
� Remove the desiccant from its silver packaging before use. � Always replace the desiccant during repair, reconnection during maintenance or reinstallation. When replacing the desiccant, use a desiccant with Service Par ts No. LW40790-001A.
CAUTION
� When connecting CN5 cable of the control board to the CN5 cable of the heater
Lug plate Silver packaging
board under cold weather conditions below 50�F (10�C), the heater will turn ON automatically and become very hot. Avoid being scalded. � Heater elements could be hot! When camera power is on, use with caution when adjusting the camera. � Make sure that the cable does not touch the components such as resistors on the heater board.
CN5 cable of heater board
CAUTION
Always use the desiccant that comes with this unit. Other desiccants or the silica gel that comes with TKC205VPU (A) are unable to remove moisture completely under extreme low temperature.
3.
1
2
5 Installing the dome cover
Refer to TK-C205VPU (A) �INSTRUCTIONS� for the installation method of the dome cover.
2. Install TK-C205VPU (A) on
the ceiling
Refer to TK-C205VPU (A) �INSTRUCTIONS� for the installation method.
6 Check items after installation
Check the following items after installation. � Is the power supply for TK-C205VPU (A) AC 24 V?
3. Install the camera unit
Align 1 and 2 of the base with 1 and 2 of the camera unit and tighten with screws. When doing this, tighten the screws of the camera unit in the order of 1, 2.
5.
Tilt lock screw Notch
� Have you inserted the desiccant that comes with this unit? � Are the CN5 cables inserted between the base and camera unit? � Does the cable touch the components such as resistors on the heater board? � Does an image appear normally on the monitor after switching on the power for TK-C205VPU (A)?
4. Adjust the field angle and
lens of the camera
Switch on the power supply of the camera. Refer to TK-C205VPU (A) �INSTRUCTIONS� on how to adjust the field angle and lens of the camera. After adjusting the field angle and lens of the camera, switch off the power supply of the camera.
Specifications
C section
CAUTION
When the heater board is installed, the switch on the camera unit is hidden and image adjustment cannot be made. Always adjust the image quality before installing the heater.
Power supply / Voltage : AC 24 V ± 10%, 60 Hz/50 Hz (recommended) Power consumption : 15 W (during AC 24 V) Heater operation : Surrounding temperature -40�F to 32�F (-40�C to 0�C) (auto on/off) *By using this unit, the operation guarantee temperature of the camera becomes -40�F to 122�F (-40�C to 50�C). Locations free from vibration and shock Locations free from salt erosion and corrosive gases Mass : 100� (total mass of heater board, control board, desiccant and screw assy) Accessories : � Instructions ............. 1 � Warranty Card ............... 1 � Service Information � Desiccant (Service Parts Card ........................ 1 No. LW40790-001A) ...... 1 � Heater unit .............. 1 � Screw assy .................... 2 * Design and specifications are subject to change without notice.
5. Install the inner cover
Mount the inner cover such that the tilt lock screw can be seen from the hole on C section. When mounting, make sure that the notch of the inner cover comes to the direction which the lens of the camera is facing.
®
® ®
is a Registered Trademark owned by Victor Company of Japan, Limited. is a Registered Trademark in Japan, the U.S.A., the U.K. and many other countries.
Printed in Thailand LWT0260-001A-H
© 2005 Victor Company of Japan, Limited
|
|
|
> |
|
