|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
KDC-C20V
TEST MODE / ADJUSTMENT / CAUTION
How to enter
1. Connect the changer to the H/U. 2. While holding the magazine eject button of the changer, press the reset button of the H/U. 3. After about 3 seconds, release the magazine eject button. 4. Press the SRC button of the H/U to enter the CD-CH mode, and the H/U�s display section indicates �E-88�. (NOTE) In the E-88 mode, the initial position detection operation at the time or reset start is not performed. operated manually using the Track UP/DOWN and Disc +/ - keys. 1. Track UP key: Operates the Spindle/Loading motor in the direction for pulling the disc tray into the mechanism deck. 2. Track DOWN key: Operates the Spindle/Loading motor in the direction for returning the disc tray into the magazine. 3. Disc + key: Operates the Elevator motor in the direction for moving the mechanism deck upward. 4. Disc - key: Operates the Elevator motor in the direction for moving the mechanism deck downward.
Manual operation functions
The E-88 display appears when the H/U is set to the changer mode. In this condition the changer mechanism can be
ADJUSTMENT
L.P.S. initial position adjustment procedure
1. Connect the changer to the H/U. 2. While holding the magazine eject button of the changer, press the reset button of the H/U. 3. After about 3 seconds, release the magazine eject button. 4. Press the SRC button of the H/U to enter the CD-CH mode, and the H/U�s display section indicates �E-88�. 5. Move the mechanism deck to around the 1st stage by pressing the DISC- or DISC+ button. 6. Insert the adjustment tool (W05-0635-00) into the tool hole on the changer mechanism. 7. Then press the DISC+ button to move the mechanism deck until the mechanism�s slider hits the adjustment tool. 8. When the motor locks (stops), press the REPEAT key of the H/U. When the REPEAT key is pressed, the mechanism moves automatically to the 1st stage and the initial position adjustment completes. (The data is written in the EEPROM at this time.)
W05-0635-00
CAUTION
Note on IC8 (EEPROM)
Be sure to use the W05-0870-00 when replacing the EEPROM. IC8 stores the digital servo data of the pick-up servo. Therefore, if the EEPROM does not store servo data, ERROR76 (E-76) will indicate the H/U' s display section at the moment CD is played.
8
|
|
|
> |
|
