|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service manual was a copy of the original from Wirlpool. The quality was good, all neccecary information was available including the service-codenumbers, so I could order the right part to be replaced for repair.
Downloding was no probem after the payment.
Thanks for the service!
;
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
;
Service Manual that I received was very helpful to me. Thank you.
;
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
KDC-MP828/W7531/W7531Y/W8531 /W8531Y/X789/X8529/X889
TEST MODE
2. When entering the test mode, the manufacture code of the Flash ROM (4M) is read and when it is normal, FROMCHK of the 100th terminal (Panel µ-com) repeats Hi � Low � Hi · · ·. If the reading is abnormal, �Low� is output. If the manufacture code is normal, by pressing [ ] key for less than 1 second, the connection checks on all terminal is started. If the connections are normal, the FROMCHK terminal stops the Hi � Low � Hi · · · repeating and outputs �Hi�. If the reading is abnormal, �Low� is output. 3. With all lights turned on and by pressing [AM] key for at least 1 second, the data on the Flash ROM (4M) is initialized. While erasing the data, �Data_Erase....� is displayed. Note : Do not touch any key white this is in progress. When erasing is complete, �Erase_OK!!� is displayed. If �Erase_NG!!!!!!� is displayed, it was not possible to erase the data on the Flash ROM (4M). In this case, pressing [AM] key for at least 1 second again. If it is the same, then there is an abnormality with the Flash ROM. � While in the test mode, and at the same time, PM_DET of the 60th terminal (System µ-com) is H, the following will apply to the EJECT key, regardless of whether a disc is in the unit or not. Panel full OPEN/CLOSE is conducted with a push for less than 1 second. (Protection time : 3 seconds) As far as this item is concerned, eject will be achieved by for at least 1 second push on the EJECT key.
� Clearing backup memory and installer memory data (Clearing E2PROM data)
1. By pressing [ ] (NEXT) key and [ATT] key simultaneously, reset and start the unit. This will start the initialization processes for backup and installer memory data and the error log information of the CD mechanism. 2. When initialization is complete, the following display will be made. Normal completion CD_E2P___: AUDIO_E2P:
� Other
� At Power ON, �CODE_OFF�, �CODE_ON� displays will not be made. � When sourcing STANDBY, by pressing [AUTO] or [TI] key for less than 1 second, GREEN/RED of the key illumination is switched. When doing this, the triangle illumination GREEN/RED is switched along with the key illumination. � When staring up in the test mode, LINE MUTE prohibition time is set to 1 second instead of 10 seconds. � While in the test mode, even when a DC offset error is detected, the detection information will not be written to the E2PROM. � While in the test mode, even after an elapse of pre-set time, the backup memory items will not be written to the E2PROM. � Information Clear mode for Test Mode, backup/installer memory, and CD mechanism error log. In the DC offset error detection information clear mode, DEMO mode operation will not be conducted. Also, in the above mode, the menu of the STANDBY source will not display DEMO ON/OFF switching items.
Abnormal ending 1 : backup/installer memory initialization : NG CD_E2P___: AUDIO_E2P:
Abnormal ending 2 : CD mechanism error log initialization : NG CD_E2P___: AUDIO_E2P:
Abnormal ending 3 : All initialization : NG CD_E2P___: AUDIO_E2P:
3. While in this mode, even after an elapse of a pre-set time, no backup memory items will be written to the E2PROM. 4. This mode is released by resetting. (What was on the last screen will not be retained.)
16
|
|
|
> |
|
