|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent service manual, the only known point of note is the alignment of improvability scanned pages within the pdf page. The resolution is good.
;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
;
It was just what I need to fix my old BMW's CD player. Very convenient also. Thank you.
;
Great Manual! It contains all the wiring schematics and mechanical exploded views that are essential for service and repair. I was surprised I even found this for such an old machine. Only wish I knew of this site many years ago.
Carrying your monitor
Be sure to grasp the areas indicated by the arrows when carrying the monitor, and to use more than two people. Never grasp the front panel.
2
Pass a strong cord or a chain through each bracket mounted in step 1, and then secure it to a wall or a pillar, etc.
Step 2: Hookup
Using the rear RGB 1 IN connector
Rear of the monitor
Using the buckle
You can also use the supplied buckle to secure the monitor to the stand.
1 VIDEO IN 3 Y DVD VIDEO OUT S VIDEO
p for KL-W7000A
Before making the connection, turn off the power and disconnect the AC power cords of the monitor and the equipment to be connected. Refer to the instruction manual of the equipment you connect.
S VIDEO
CB/PB CR/PR
VIDEO
VIDEO L AUDIO R
Connecting to an IBM PC/AT or compatible computer
p for KL-W9000A
RGB
RGB 1 IN AUDIO R L
1
Attach the buckle to the stand on which the monitor is mounted. Tighten the supplied screw firmly.
Connect the RGB 2 IN connector on the front or the RGB 1 IN connector at the rear of the monitor to the video/audio outputs of the computer using the supplied RGB signal cable (D-sub 15 pin � D-sub 15 pin).
or
US
� 8 �
2
Stabilizing the monitor Using the brackets
After setting up, secure the monitor to a wall, etc. with the supplied brackets.
Belt
Using the front RGB 2 IN connector
Front of the monitor
RGB signal cable (supplied) or
Audio connecting cord (phono plug � 2 � stereo minijack) (not supplied)
VIDEO 2 IN VIDEO
INPUT SELECT
Insert the buckle until it clicks.
L AUDIO R
RESET
HD15�HD15 adaptor (supplied)*
RGB
AUDIO
Male side (without the No.9 pin) to video output to audio output
RGB 2 IN
1
Mount the two supplied brackets with the screws to the upper rear sides of the monitor.
IBM PC/AT or compatible computer
3
Pull the belt to fasten.
RGB signal cable (supplied) or
Audio connecting cord (stereo minijack � stereo minijack) (not supplied)
* The HD15�HD15 adaptor (supplied) may be needed for some models. The male side (without the No. 9 pin) of the adaptor should be connected to the computer.
Bracket (supplied)
HD15�HD15 adaptor (supplied)*
For customers using the supplied HD15�HD15 adaptor This monitor uses a No. 9 pin in the video signal connector for DDC1 and DDC2B compatibility. Some PC systems which are not compatible with either DDC1 or DDC2B may not accept the No. 9 pin. If you are not sure whether your PC system accepts the No. 9 pin or not, use the HD15 (Female) � HD15 (Male without the No. 9 pin) adapter (supplied).
Male side (without the No.9 pin) to video output to audio output IBM PC/AT or compatible computer
6-US
Getting Started
Getting Started
7-US
|
|
|
> |
|
