|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
 ;
Good manual. Even it is an old printed manual, it is well scanned and complete, with all drawings, schematics and parts list. Very good return for the cost.
KMD-PS971R/X92
TEST MODE
(10) Simplified security code clear procedure (KMD-X92 only) 1. During the code request mode, while holding the "DISP" key depressed, press and hold the volume "UP" key for 3 seconds (so that "----" disappears). 2. Enter "KCAR" from the remote control unit. Press numeric key "5" 2 times and press the track "UP" key (to enter "K"). Press numeric key "2" 3 times and press the track "UP" key (to enter "C"). Press numeric key "2" 1 time and press the track "UP" key (to enter "A"). and press the track "UP" key (to enter "R"). 3. The security is canceled and the set enters the tuner mode. (11) MASK key writing procedure (When the EEPROM is in the initial status) 1. While holding the "FM" and preset "6" keys depressed, press "RESET" to enter the test mode. 2. Press and hold the "AUDIO" key for 1 second to enter the menu mode. 3. Press the "FM" or "AM" key to select "Mask key". 4. Press the track "UP/DOWN" key shortly so that "TRANSMIT1" is displayed. 5. Point the MASK key to the light sensor and press and hold the key for more than 0.5 second. 6. When "TRANSMIT2" is displayed, press and hold the MASK key again for more than 0.5 second. Note that the first and second counter codes are not compared at this time. 7. The writing operation is completed when "APPROVED" is displayed. At this time, the demonstration mode is set and the test mode is canceled. (Note) Leaving the unit for more than 30 minutes without writing the code causes an error and turns power off. (12) Procedure for canceling the MASK key request (when the unit is reset or the back-up power is turned off while the MASK key is enabled) 1. When the power is supplied and the unit is switched on, "TRANSMIT1" is displayed and the MASK key request mode starts. 2. Point the MASK key toward the light sensor and press and hold for more than 3 seconds (until the level indicator indicates the full condition). 3. When "TRANSMIT2" is displayed, press and hold the MASK key again for more than 3 seconds. If "TRANSMIT1" is displayed now, go back to step "2" and restart from there again. 4. When "APPROVED" is displayed, the MASK key is enabled and the set is turned on. (13) Procedure for MASK key initialization 1. While holding the "FM" and preset "6" keys, press "RESET" to enter the test mode. 2. "TRANSMIT1" is displayed and the MASK key request mode starts. At this time, the display shows "* *" in place of "[ ]". 3. Press the MASK key canceling remote control for more than 3 seconds. 4. When "TRANSMIT2" is displayed, press and hold the MASK key again for more than 3 seconds. 5. When "APPROVED" is displayed, the MASK key is canceled, the demonstration mode is set, the test mode is canceled. (14) MASK key all-clear procedure 1. While holding the "FM" and preset "6" keys, press "RESET" to enter the test mode. 2. Press and hold the "AUDIO" key for more than 1 second to enter the menu mode. 3. Press the Track "UP/DOWN" key to select "Mask key". 7 Press numeric key "7" 2 times
|
|
|
> |
|
