|
|
|
Who's Online
There currently are 5754 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Scan quality is very good. Price is very reasonable. If you're looking to purchase a copy of this manual, this is the one to get.
 ;
Perfect for my use.Could have better pictures,but otherwise perfect ;)
;
This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
;
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
;
The manual was exactly what I wanted and I found it nowhere else. Thanks!
3. Before using the KR-3
3.1 Setting up the music rest
The music rest sets up easily with two sections folding to the inside. To put the stand away, hold it �rmly with your hands, undo the �ttings, and slowly collapse the rest.
KR-3 � Connecting the power cable
3.4 Using headphones
You can connect one or two pairs of stereo headphones (preferably Roland RH-25, RH-50) that carry the same signal as the one sent to the OUTPUT R, L/ MONO jacks. Connecting a pair of headphones to one of the PHONES jack turns off the built-in speakers. There are two jacks, so that two pairs of headphones can be connected.
3.2 Connecting the power cable
1. Set the [POWER] switch on the front panel (left side) to the OFF position. 2. After plugging the power cable included with your instrument into the AC IN jack, plug the other end into a wall socket.
Note: If you are not going to use the instrument for some time, unplug the power cord from the socket.
LEFT side (below the keyboard) LEFT SIDE (below
the keyboard)
Twopairs of headphones can be conTwo pairs of headphones nected. can be connected.
The volume of the headphones can be adjusted using the main [VOLUME] knob.
Note: Please use stereo headphones, preferably the Roland RH-50, RH-25. Note: Listening at excessive volume levels for extended periods may result in impaired hearing � please take appropriate caution.
3.3 Turning the instrument on and off
1. Before turning the instrument on, lower the volume with the [VOLUME] knob on the front panel.
3.5 Connecting external ampli�ers and other devices
If the KR-3�s ampli�cation system doesn�t deliver enough power for your application, you can take advantage of its OUTPUT jacks.
Sending audio to external equipment
2. Press the [POWER] switch to the left of the keyboard.
The power is onON when the switch pressed. The power is when the switch is is pressed.
ON OFF
Before connecting the KR-3 to another piece of equipment, turn off the power to both devices. If you wish to amplify the KR-3 through an external system, or record your music using a tape recorder, connect the KR-3�s OUTPUT jacks to the AUX IN, LINE IN, or CH IN jacks of the external (keyboard) ampli�er, mixer, or tape deck.
The power is offOFF when the switchpressed. again. The power is when the switch is is pressed
A few seconds after turning the power on you will be able to hear the notes you play on the keyboard.
Note: In order to protect its circuits, the instrument requires a few moments after powering up before it is ready for operation.
ENGLISH ENGLISH ENGLISH ENGLISH
To the AUX IN/LINE IN jacks of the external ampli�er/ mixer, etc.
Note: If you are connecting the KR-3 to a device with a monaural input, be sure to use the L/MONO jack. Note: For cassette decks or HiFi ampli�ers, you need audio leads with mono jacks at one end and (usually) RCA/cinch jacks at the other.
9
|
|
|
> |
|
