|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
;
I was skeptical at first but later found the manual to be good quality for the price. It took a couple hours to receive the email with the download link, well worth the wait. Thanks.
KRC-165
TEST MODE / ADJUSTMENT
TEST MODE
1. How to enter the test mode
� Reset the unit while holding the Track Down key and preset 6 key. � All indication segments go ON at the beginning of the test mode. � The BASS / TREBLE and BALANCE / FADER controls can be set to the full boost / center / full cut and full right / center / full left and full front / center / full rear respectively. � Sound coordination doesn't appear for the Audio mode feed. � The inspection function of LCD When all indication segments are ON, the segments can be set to the following order respectively by pressing the Track up key / Track down keys. All indication segments � Odd segments (Common 1 part) � Even segments (Common 2 part) � Odd segments (Common 3 part) � All indication segments � When the unit is reset (backup turned on) while ACC is OFF in test mode, the MUTE terminal goes off in 2 seconds.
2. How to release the test mode
� Simply reset the unit. � (NOTE) The test mode is not canceled by ACC OFF, power OFF, momentary power down or the panel off.
3. Contents
� Set the volume level to -10dB (which is shown as "30" on the display). � Loudness OFF.
ADJUSTMENT
Set the controls and switches as follows. BALANCE : center position BASS : center position FADER : center position TREBLE : center position No. ITEM TAPE OUTPUT SETTINGS LOUDNESS : OFF
RECIEVER SETTINGS
ALIGNMENT POINTS
ALIGN FOR
CASSETTE DECK SECTION
[1]
HEAD HEIGHT
SCC-1659
-
TAPE PLAY
Head Height Screw
1) During FWD transport adjust �and �' so that line A F F of 2-LINE TAPE passes through the center of the head shield plate (core center area) 2) During RVS transport adjust � and � ' so that line B R R of 2-LINE TAPE passes through the center of the head shield plate (core center area) 3) After the alignment above, reverse the transport direction and check the FWD alignment again. If it is deviated, perform alignment again. (Tape used : SCC-1659, manufactured by A-BEX) Adjust the azimuth for each L ch/R ch or FWD/RVS becomes maximum.
[2]
HEAD AZIMUTH
TCC-153 10kHz
Connect an AC voltmeter and oscilloscope to SP outputs.
TAPE PLAY
Head Azimuth Screw
TAPE SPEED
(2-LINE TAPE)
B A (FWD)
HEIGHT (FWD)
F
'
R
'
HEIGHT (RVS)
B
HEIGHT/AZIMUTH (FWD)
F R
A
(RVS)
HEIGHT/AZIMUTH (RVS)
6
|
|
|
> |
|
