|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the original Service Manual from Nordmende, Germany. Contains the circuit diagram, PCB layout, adjust/tune instructions as well. It is NOT in English but in GERMAN language! That was quite right for my german friend from the lower east side in Berlin.
 ;
Received via e-mail this PDF manual is worth the money. This is a quality scan of a manual in excellent condition and is just as good as having the original manual in hand. I have later seen the original manual and it was printed in colour, but this particular manual is black & white but scan resolution is high end quality! All drawings and pictures are presented in great detail. So, nearly perfect score in my opinion.
If you own the turntable you also should own the manual!
;
I was very satisfied with the service manual I ordered and downloaded. I will definitely buy again from this seller.
;
Great product. Recieved it fast...exactly as advertised.
;
Manuals were delivered promptly and were correct as advertised. No issues with the download link which was provided promptly after everything was processed. Very pleasant experience
KRC-19A/G,289
MICROCOMPUTER'S TERMINAL DESCRIPTION
¶ Terminal Description IC1 : MI-COM. (X14-)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17-24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45-47 48 49 50 51 52 53 54 55 56 57-60 61 Pin Name XIN GND L DATA L L DATA S L CLK L CE SDA PLL DATA PLL CLK SD DATA C DATA H CH CLK MOTOR SCL AM+B FM+B PACK IN FF/REW GND GND VDD REQ C MUTE CH CON REQ H SVR AMP STBY AMP MUTE P CON ANT CON SW5V ILL BEEP ROLL OFF NOISE CANCELLER SEL1 SEL2 EQ MUTE FWD/REV REMO ACC DET I/O I I O O O I/O I/O O I I O I/O O O O O O O I I I I I O O O O O O O O O O O O O I I I I O O I O I O I Description Main clock resonator connection terminal TEST terminal 2 Data input from the LCD driver IC Data output to the LCD driver IC Clock output to the LCD driver IC CE output to the LCD driver IC Data input/output with the E-VOL. IC Data input/output with the F/E Clock output to the F/E SD input from the F/E Data input from changers Data output to changers Clock input/output with changers Cassette motor on/off output Clock output to the E-VOL. IC Processing Operation Connected to GND lines.
Hi : Station detected
N.C.(Not used) Hi : Motor ON
N.C.(Not used) AM+B ON/OFF output Hi : during AM reception FM+B ON/OFF output Hi : during FM reception Cassette tape Pack-in detection input Lo : Pack-in FF/REW detection input Lo : FF/REW, Hi : PLAY Connected to GND lines. Connected to GND lines. VDD connection terminal Connected to B.U. 5V lines. Request input from changers Lo : Request Audio mute on/off output Hi : Mute ON Changer control Lo : Standby, Hi : ON Request output to changers Lo : Request When the momentary power down, after Power IC reset terminal ACC ON/OFF is detected and after POWER OFF, the output becomes Hi temporarily. Power IC standby control output Hi : POWER ON mode Power IC mute control Lo : Mute Power control Hi : POWER ON mode Antenna control Hi : during FM/AM reception SW 5V control Lo : POWER ON mode Illumination AVR ON/OFF control terminal Hi : POWER ON mode N.C.(Not used) BEEP sound output N.C.(Not used) Roll off input Pull down to GND lines. (Not used) Noise canceller input Pull down to GND lines. (Not used) Destination input 1 Lo : KDC-19A/G, Hi : KDC-289 Destination input 2 Pull down to GND lines. (Not used) N.C.(Not used) Tape equaliser mute on/off output N.C.(Not used) FWD/REV detection input Lo : REV mode N.C.(Not used) Data input from the remote control light Pull down to GND lines. (Not used) sensor N.C.(Not used) ACC detection input Hi : ACC ON
4
|
|
|
> |
|
