|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
 ;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
 ;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
 ;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
 ;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
KRC-19A/G,289
MICROCOMPUTER'S TERMINAL DESCRIPTION
¶ Terminal Description IC1 : MI-COM. (X14-)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17-24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45-47 48 49 50 51 52 53 54 55 56 57-60 61 Pin Name XIN GND L DATA L L DATA S L CLK L CE SDA PLL DATA PLL CLK SD DATA C DATA H CH CLK MOTOR SCL AM+B FM+B PACK IN FF/REW GND GND VDD REQ C MUTE CH CON REQ H SVR AMP STBY AMP MUTE P CON ANT CON SW5V ILL BEEP ROLL OFF NOISE CANCELLER SEL1 SEL2 EQ MUTE FWD/REV REMO ACC DET I/O I I O O O I/O I/O O I I O I/O O O O O O O I I I I I O O O O O O O O O O O O O I I I I O O I O I O I Description Main clock resonator connection terminal TEST terminal 2 Data input from the LCD driver IC Data output to the LCD driver IC Clock output to the LCD driver IC CE output to the LCD driver IC Data input/output with the E-VOL. IC Data input/output with the F/E Clock output to the F/E SD input from the F/E Data input from changers Data output to changers Clock input/output with changers Cassette motor on/off output Clock output to the E-VOL. IC Processing Operation Connected to GND lines.
Hi : Station detected
N.C.(Not used) Hi : Motor ON
N.C.(Not used) AM+B ON/OFF output Hi : during AM reception FM+B ON/OFF output Hi : during FM reception Cassette tape Pack-in detection input Lo : Pack-in FF/REW detection input Lo : FF/REW, Hi : PLAY Connected to GND lines. Connected to GND lines. VDD connection terminal Connected to B.U. 5V lines. Request input from changers Lo : Request Audio mute on/off output Hi : Mute ON Changer control Lo : Standby, Hi : ON Request output to changers Lo : Request When the momentary power down, after Power IC reset terminal ACC ON/OFF is detected and after POWER OFF, the output becomes Hi temporarily. Power IC standby control output Hi : POWER ON mode Power IC mute control Lo : Mute Power control Hi : POWER ON mode Antenna control Hi : during FM/AM reception SW 5V control Lo : POWER ON mode Illumination AVR ON/OFF control terminal Hi : POWER ON mode N.C.(Not used) BEEP sound output N.C.(Not used) Roll off input Pull down to GND lines. (Not used) Noise canceller input Pull down to GND lines. (Not used) Destination input 1 Lo : KDC-19A/G, Hi : KDC-289 Destination input 2 Pull down to GND lines. (Not used) N.C.(Not used) Tape equaliser mute on/off output N.C.(Not used) FWD/REV detection input Lo : REV mode N.C.(Not used) Data input from the remote control light Pull down to GND lines. (Not used) sensor N.C.(Not used) ACC detection input Hi : ACC ON
4
|
|
 |
> |
|