|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
KRC-17G/YA/YG, 194A/G/YA/YG, 266LA/LG/RG KRC-27YA/YG, 2904YA/YG, 294A/G/YA/YG
ADJUSTMENT
No ITEM INPUT SETTINGS RECEIVER SETTINGS ALIGNMENT POINTS ALIGN FOR
FM SECTION
1
SD
98.1MHz 0 dev 35dBµ(ANT input)
TEST MODE: ON FM 98.1MHz
Preset "1" key, and preset "6" key
While holding preset "1" key, press and hold preset "6" key for a few seconds. "ADJ OK" is good. "ADJ NG" is not good.
AM SECTION
(1)
SD
990 kHz 0% mod 35dBµ(ANT input)
TEST MODE: ON AM 990 kHz
Preset "1" key, and preset "6" key
While holding preset "1" key, press and hold preset "6" key for a few seconds. "ADJ OK" is good. "ADJ NG" is not good.
CASSETTE DECK SECTION
[1]
HEAD HEIGHT
SCC-1659
TAPE PLAY
Head Height Screw
1) During FWD transport adjust F and F ' so that line A of 2LINE TAPE passes through the center of the head shield plate (core center area) 2) During RVS transport adjust R and R ' so that line B of 2LINE TAPE passes through the center of the head shield plate (core center area) 3) After the alignment above, reverse the transport direction and check the FWD alignment again. If it is deviated, perform alignment again. (Tape used : SCC-1659,manufactured by A-BEX)
[2]
HEAD AZIMUTH
TCC-153 10kHz
Connect an AC voltmeter and oscilloscope to SP outputs. TAPE PLAY
Head Azimuth Screw
Adjust the azimuth for each L ch/R ch or FWD/RVS becomes maximum.
TEST MODE : ON TEST MODE : OFF
While holding the "FM" key and preset "6" key, reset the unit. Reset the unit.
TAPE SPEED
(2-LINE TAPE)
B
HEIGHT (FWD)
F
'
R
'
A (FWD)
HEIGHT (RVS)
B
HEIGHT/AZIMUTH (FWD)
F R
HEIGHT/AZIMUTH (RVS)
A
(RVS)
5
|
|
|
> |
|
