|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
;
Exactly what was needed to assess the product - excellent value and great service
;
A site where discontinualed schematic diagrams and back dated information can be found on discontinued radios tv's and any electronic equipment can be found. Newer manuals either Service and operating manuals. Radio amateurs should find this site a great source for ham radio equipment manuals. I will return to this site should I need information on any electrical equipment. priced easy to download in a PDF format and print pages need to undertake the repair.
;
Quality scan of the original. All the detail necessary to troubleshoot, repair and adjust the unit. I'm sure I will be downloading more manuals in the future as the need arises.
;
Exactly as described, a Service Manual complete with the schematics and PCB layout delivered in a timely manner. Many thanks for the great service.
KRC-391/Y,36/Y,30Y
MICROCOMPUTER'S TERMINAL DESCRIPTION
PORT No. PORT NAME I/O FUNCTION 57 FWD/REV I Cassette tape running direction detection. 58 SUB+ O Sub motor control. 59 SUBO Sub motor control. 60 RESET I System reset. 61 REMOTE I Remote control. 62 R-CLK I RDS clock. 63 CH-REQ C I Changer request. 64 PACK-IN I Cassette tape pack-in detection. 65 KEY-REQ I Key signal detection. 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 VSS0 VDD1 X2 X1 IC XT1 VDD0 AVREF 0 S-METER T-MODE PHONE NOISE AV CONT I I I I I I O GND. VDD. Main system clock. Main system clock. VDD. VDD. Reference voltage. SD detection. Cassette tape mode detection. Navi mute: Over 2.5V. Tel mute: less than 2.5V. Noise detection during FM mode. Reference voltage. OPERATING CONDITION "H": FWD "L": REV.
KRC-391/Y,36/Y,30Y
TEST MODE / ADJUSTMENT
TESTMODE
1. How to enter the test mode
� Reset the unit while holding the "FM" key and preset "6" key. � All indication segments go ON at the beginning of the test mode.
4. Audio adjustment
� Enter the audio mode by pressing the "AUD" key or "OPEN/CLOSE" key on the remote controller. � Set the volume level to be -10dB. In that case, "30" should be shown on the display. � Loudness OFF. � The BASS/MIDDLE/TREBLE and BALANCE/FADER can be adjusted to the full-boost/full-cut and full-front/ full-rear each by pressing the "UP" and "DOWN" keys.
2. How to release the test mode
� Simply reset the unit. � (NOTE) The test mode should not released in conditions of ACC OFF, power OFF, momentary power down or the panel off.
5. Menu mode
� Enter the menu mode by pressing "CLK" key or "DNPP" key on the remote controller. � Only on models with RDS function, Local Seeking should be first menu.
3. Test mode
� Blanking Skip (B.S) OFF. � Eject a tape by pressing "ATT" key. "H": SD exists. "L": SD does not exist.
ADJUSTMENT
BALANCE/FADER/BASS/TREBLE : CENTER T.ADV/METAL/DOLBY NR/AUTO : OFF No. INPUT SETTINGS CASSETTE DECK SECTION ITEM AZIMUTH TCC-153 10kHz OUTPUT SETTINGS RECEIVER SETTINGS ALIGNMENT POINTS Head azimuth screw (FWD/REV) (ME1) ALIGN FOR Adjust so that output level in playing "FWD" and "REV" becomes maximum each. FIG.
1
SP OUT
TAPE PLAY
(b)
(b) AZIMUTH
FWD
REV
PANEL FRONT
5
6
|
|
|
> |
|
