|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The Service Manual for the Kenwood KR-V55R provided by owner-manuals.com was as described/advertised. The contents provided the necessary information to effect a diagnosis of the unit. The schematics above all else was instrumental in tracing the the signal flow from component to component.
 ;
This manual was the factory original. Excellent value and contained all the details I needed. Easy dowwnload provided the information when I needed it.
;
Impeccable, document très complet. Perfect, i get all i need. All schematic are correct. Thanks
;
The manual is of better quality compared to other. I found it less expensive and therefore it it is the best buy cost vs quality.
;
I bought the service-manual of the sony ICB-1020(an old transmitter-receiver) at "www.Owners-Manual.com", I found the service-manual for a fairly cheap price(in comparison with other sellers). I filled in some questions, payed the order with Ideal, and within 24 hours I had my service manual. I was very happy:In no time I had my service-manual and everything, but literally everything was noted down in the manual; the electronic scheme, the parts list, etcetera.
A very practical, reference-document.
KRC-31Y/36/366L/37/Y /391/394/Y/466R/4904Y
MICROCOMPUTER�S TERMINAL DESCRIPTION
q Microcomputer : UPD780058GCxxx (X14 : IC1)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Pin Name DSI PANEL AVSS L-RST L-CE AVREF1 PLL-DATA PLL-CLK L-DATA L L-DATA S L-CLK R-DATA R-QUAL CH-DATA C CH-DATA H CH-CLK M-STBY T-END ACC-DET BU-DET IC2 TYPE 0 IC2 TYPE 1 TYPE 0 TYPE 1 TYPE REF I/O O I O O I I/O O I O O I I I O I/O I �H� : Standby I I I I I I I O and service. 28 29 30 31 32 33 34 35 36 37 38 39 40 MOTOR PLL-CE SD ASF LO/DX VSS1 P-MUTE SVR IC2-SCL IC2-SDA MUTE P-STBY O O I �L� : Station does not exist O O O O O I/O O O Noise detection time constant switch. Local seeking switch. �H� : LO, �L� : DX GND. Power amplifier muting. SVR control. E-volume communication clock. E-volume communication data. Muting control. Power amplifier standby. 78 79 80 PHONE NOISE AV CONT I I O 76 77 S-METER T-MODE I I 73 74 75 XT1 VDD0 AVREF 0 I VDD. VDD. Reference voltage. SD detection. �H� : SD exists, �L� : SD does not exist Cassette tape mode detection. Navi mute : Over 2.5V, Tel mute : Less tha 2.5V Noise detection during FM mode. reference voltage. Cassette mechanism motor. �H� : ON, �L� : OFF Front-end communication ship enable. Station detection. �H� : Station exists, 68 69 70 71 72 VDD1 X2 X1 IC I VDD. Main system clock. Main system clock. Tape end detection. �H� : Run, �L� : Stop ACC detection. Backup detection. For service. �L� : Normally For service. �L� : Normally Destination discrimination. Destination discrimination. Reference voltage for destination 59 60 61 62 63 64 65 66 67 SUBRESET REMOTE R-CLK CH-REQ C PACK-IN KEY-REQ VSS0 O I I I I I I Sub motor control. System reset. Remote control. RDS clock. Changer request. Cassette tape pack-in detection. Key signal detection. GND. Function / Operating Condition DSI control. Panel detection. �L� : Panel exists GND. LCD driver reset. LCD driver chip enable. Reference voltage. Front-end communication data. Front-end communication clock. LCD driver communication data. LCD driver communication data. LCD driver communication clock. RDS data. 55 RDS QUAL. Changer communication data. Changer communication data. Changer communication clock. Cassette tape standby detection. 57 58 FWD/REV SUB+ I O 56 EQ-MUTE O MS-CONT O �H� : Play, �L� : FF/REW Cassette tape muting. �H� : ON, �L� : OFF Cassette tape runing direction detection. �H� : FWD, �L� : REV Sub motor control. 54 MUSIC I Pin No. 41 42 43 44 45~47 48 49 50 51 52 53 Pin Name P. CON-DET CH-CONT CH-REC H EN2-1 EN2-0 BEEP EN3 EN1 SW 5V I/O I O O O O O O O O Function / Operating Condition P. CON short-circuited detection. Changer control. Changer request. Power supply IC control. Power supply IC control. Buzzer. Power supply IC control. Power supply IC control. P. ON 5V control. �H� : OFF, �L� : ON Tape signal detection. �H� : Signal does not exist, �L� : Signal exists tape advanced sensitivity control.
4
|
|
|
> |
|
