|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
 ;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
KRC-435/665
TEST MODE
10. Special display when the display is All ON
If the PRESET key is pressed while all displays are turned on by ALL OFF, the following display appears. Version display (8 digits, Month/Day/Hour/Minute) (Display) xxxxxxxx System microcomputer PRESET 2 All displays are turned on. Short press : Power-ON time display PRESET 3 Long press : Power-ON time is cleared. (Display) Pon xxxxx Max. 65535 (hours) Short press : TAPE/CD/MD running hour display PRESET 4 Long press :TAPE/CD/MD unning hour is cleared. (Display) CDT xxxxx (CD/R) TPT xxxxx (C/R) Max. 65535 (hours) Short press :TAPE/CD/MD eject count display PRESET 5 Long press :TAPE/CD/MD eject count is cleared. (Display) EJT xxxxx Max. 65535 (times) Short press : PANEL open/close count display PRESET 6 Long press : PANEL open/close count is cleared. (Display) PCX xxxxxx Max. 65535 (times) PRESET 1 2. Enter the security registration mode by pressing the CLK key. 3. Enter the CODE by pressing the Track up/down and AM/ FM key. Example: To enter "3510" � Press the FM key four times. � Press the Track up key once and the FM key six times. � Press the Track up key once and the FM key twice times. � Press the Track up key once and the FM key once times. � When the AM key is pressed, the codes are searched in reversed direction. When Track down key is pressed, the entry digits return. 4. When the DISP key is pressed for three seconds, the message "RE-ENTER" appears. Then enter the code referring to step 3. 5. Press the DISP key for three second so that the message "APPROVED" appears. 6. Quit the test mode. (See item 2. How to quit the test mode.) (Note) The security code of this model cannot be all cleared.
� Write timing into EEPROM is when ACC OFF and POWER OFF sequence is completed.
� Simple security code clear procedure (K type only)
1. Press the VOL UP key longer for 3 seconds while pressing the DISP key during requesting the code. (The message ---- disappears.) 2. Enter "KCAR" from remote control. (Same as the 00 model) � Press the 5 key twice on remote control and press the Track up key. (Enter "K".) � Press the 2 key on the remote 3 times, then press the Track Up key. (This enters "C".) � Press the 2 key on the remote once, then press the Track Up key. (This enters "A".) � Press the 7 key on the remote twice, then press the Track Up key. (This enters "R".) 3. The security is released and the product enters the ALL OFF mode. 4. If incorrect code is entered by mistake, the product enters the code-requesting mode.
11. Others
� Displays such as "CODE OFF" are not shown during Power-ON. � When the CLK key is pressed longer for 1 second during ALL OFF, the product enters the MASK KEY (security) write mode. � The RESET-LOADING is not performed unless CD is already caught in the CD/R mode.
s Security-related information
� Forced Power ON mode (All models)
Even when security (MASK key) is enabled, the product can be powered ON for 30 minutes only by pressing the RESET key while both of the ATT key and the Preset 4 keys are being pressed. The product will recover only by RESET if 30 minutes have elapsed.
� Security code registration procedure (code security model) after EEPROM (F/E) is replaced.
1. Let the product enter the test mode. (See 1. How to Enter Test Mode) 7
|
|
|
> |
|
