|
|
|
Who's Online
There currently are 5983 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
Setting up the system
Connecting the terminals
1 Strip coating. 2 Loosen.
Speaker placement
Center speaker
3 Insert.
4 Secure.
Subwoofer Front speakers (L,R) Surround speakers (L,R)
1 Strip coating. 2 Push the lever.
Listening position
Surround back speaker
3 Insert the cord.
4 Return the lever.
Front speakers : Place at the front left and right of the listening position. Front speakers are required for all surround modes. Center speaker : Place front and center. This speaker stabilizes the sound image and helps recreate sound motion. Required for surround playback. Surround speakers : Place at the direct left and right, or slightly behind, the listening position at even heights, approximately 1 meter above the ears of the listeners. These speakers recreate sound motion and atmosphere. Required for surround playback. Subwoofer : Reproduces powerful deep bass sounds. Surround back speaker : Place the speaker directly at the rear of the listening position. The optimum position depends mainly on the room condition.
Connection of banana plugs (For the U.S.A. and Canada)
1 Secure. 2 Insert.
� Although the ideal surround system consists of all the speakers listed above, if you don't have a center speaker or a subwoofer, you can divide those signals between the available speakers in the speaker settings steps to obtain the best possible surround reproduction from the speakers you have available. *
� Sound will not be heard if the speaker terminal is not fully secured. � Never short circuit the + and � speaker cords. � If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly.
Channel space switching
(Except for the U.S.A., Canada, U.K., and Australia)
The space between radio channels has been set to the one that prevails in the area to which the system is shipped. However, if the current channel space setting does not match the setting in the area where the system is to be used, for instance when you move from area 1 or area 2 shown in the following table or vice versa, proper reception of AM/FM broadcasts cannot be expected. In this case, change the channel space setting in accordance with your area by referring to the following table. Area 1 2 U.S.A., Canada and South American countries Other countries CHANNEL Space Frequency FM: 100 kHz AM: 10 kHz FM: 50 kHz AM: 9 kHz
Speaker impedance
After confirming the speaker impedance indications printed on the rear panel of the receiver, connect speakers with matching impedance ratings. Using speakers with a rated impedance other than that indicated on the rear panel of the receiver could result in malfunctions or damage to the speakers or receiver.
75us AM 10kHz FM100kHz
50us AM 9kHz FM50kHz
75us AM 10kHz FM100kHz
50us AM 9kHz FM50kHz
DE-EMPHASIS CHANNEL SPACE
DE-EMPHASIS CHANNEL SPACE
Turn the power OFF by pressing the POWER key before moving the switch level. Move switch lever to match your area with a small screwdriver or other pointed tool, then turn the power on again.
15 EN
|
|
|
> |
|
