|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I had been looking for a Manual for my CS2150 for quite a while -- in fact I had just about given up. I saw this site and decided to download the Manual. When I Received it by Email I was really pleased with what I got, with the result that My Kenwood 'Scope is now 100% repaired and working well. As an AV Serviceman, you need a good 'scope, and thanks to this site, and the Service Manual, I have been able to repair it. The Manual was a copy of the Factory Original and the copy was very clear, especially in the area of the Circuit Schematics, where You really need to be sure of what You are looking at.
;
I recently purchased a manual for a Samsung DLP tv to help with a trouble shooting problem I was having. Every tv repair shop wanted close to $400.00 for the fix, but after I found Owner-Manuals.com I hit pay dirt. The manual they had for me to purchase and download was a complete service manual for the exact tv I needed. It was complete with wiring diagrams, schematics, and even part numbers. If your the fix it yourself type I highly recommend trying to find any manual here before paying someone else to fix whatever problem your having.
;
Once again, excellent price and manual delivered in a timely manner and as advertised!
;
Outstanding quality manual. This is the exact documentation I needed to service my AKAI GX-210D. This is a PERFECT COPY of the service manual for my machine. Outstanding service. Thank-you!
;
This service manual have great value... Recommended A+++++++
1
2
3
4
A
Preparation
� Set the MR from System Operation mode to Standalone Operation mode. The MR is normally set to System Operation mode. If the MR is turned on in this mode, an error warning is issued (the red and blue LEDs alternately flash), and it cannot be operated properly. To change to Standalone Operation mode, proceed as follows: [With an RS-232C command] 1. Turn the MR on. (The red and blue LEDs alternately flash to warn of an error.) 2. In this state, send the MRMS01 command via RS-232C ports. 3. Turn the MR off. When the MR is turned on next time or after, it will be in Standalone Operation mode. [With the keys on the MR] 1. Set the MR to Standby mode. 2. Press and hold the INPUT key of the MR pressed for at least 5 seconds. (This step is for giving a startup trigger in a case where the MR was in Passive Standby mode.) 3. Within 5 seconds after the INPUT key is released, press and hold the CHANNEL - key of the MR for at least 10 seconds. 4. After the modes are changed, the red LED flashes twice then is lit (the unit enters Normal Standby mode). 5. Turn the unit off. When the MR is turned on next time or after, it will be in Standalone Operation mode.
B
C
Operation
After the setting in Preparation is completed, turn the units on in the following order then perform analysis: 1. Turn the monitor or TV on. (Set the input mode to HDMI.) 2. Turn the DP-to-HDMI conversion jig on. 3. Turn the MR on. If no image is displayed on the monitor or TV after the MR is turned on, press and hold the switch on the DP-to-HDMI conversion jig for about 1 sec.
How to control the MR
D
� With the remote control unit: The infrared receiver (IR) sensor for remote control unit is placed inside of the jig. Please point the remote towards the AC adaptor connector on the jig. Unlike normal products, sensor reception of this tool is not so sensitive due to reduce interference with another Pioneer Plasma TV. Please keep the distance between the remote control unit and the sensor less than 15cm. � With RS-232C commands: Connect a PC to the MR via their RS-232C ports and send RS-232C commands from the PC. (Baud rate: 9600 bps)
E
F
70
1 2
KRP-M01
3 4
|
|
|
> |
|
