|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
KV-27FV310/29FV310/32FV310/36FV310
2-4. SCREEN (G2)
1. 2. 3. 4. Input dot pattern from the pattern generator. Set the user controls to NORMAL. Attach the G2-Jig to the C Board. Adjust RCUT, GCUT, BCUT, and SBRT in service mode with an oscilloscope so that voltages on the red, green, and blue cathodes are 170 ± 4.0Vdc.
2-5. WHITE BALANCE ADJUSTMENTS
���� ������� ������� ������� ������� ������� ������� ���
1. 2. 3. 4. 5. 6. 7.
��� ����� � � � � � � � ���� ����
���� ��� ����� ���� �����
��� ������ �� �� �� �� �� �� ��
���� ����� ����� ���� ��� ������� ���� ����� ������� ���� ���� ������� ���� ��� ������
5. Observe the screen and adjust SCREEN (G2) VR to obtain the faintly visible background of dot signal. 6. Push the TEST + JUMP (+ Channel) to cut off the signal. The screen should be bright or dark. Brightness of raster must be increased when adjusting. 7. Adjust screen VR until the screen is slightly cut off, or scarcely lights up. A signal cannot be seen when the brightness of the raster is high. 8. Push the JUMP again to release the cut off. .
170 + 4.0 Vdc 170Vdc
GND
pedestal
Set program palette to STANDARD and push RESET. Input an entire white signal. Set to Service Adjustment Mode. Set the PICTURE and BRIGHT to minimum. Adjust with SBRT if necessary. Set RCUT to �14�. Select GCUT and BCUT with 3 and 5 .
8. Adjust by pressing 1 and 4 for the best white balance. 9. Set the PICTURE and BRIGHT to maximum. 10. Select GDRV and BDRV with and . 11. Adjust with 3 and 6 for the best white balance. 12. Write into the memory by pressing 3 then 5 . 13. Repeat steps 1-12 for GDR4, BDR4, GCU4 and BCU4 using Video 4 input. * Use values from Sub Contrast Adjustments White balance should be adjusted after Sub Contrast because RDRV is also used in Sub Contrast Adjustment. (See page 26)
� 15 �
|
|
|
> |
|
