|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I do not have very much to say.
The price is quite covenient, delivery was better as promised (about 12 ours, against the specified 24 hours if I remember well), and the quality of the PDF is more than acceptable.
The Service Manual of Sansui R30 itself is also satisfactory: good graphic for schematics and layouts, simple and well structured.
Giovanni Bianchi
 ;
Happy to find finally a schematic for this amplifier. The schematic is of good quality, the pcb layout is useless: all is black. Never the less, it is very easy to find the components on the board using the schematics.
 ;
Hard to find manual was ready the next day. Scans were very legible (including schematics). All the essential parts of the service manual were present (adjustment procedure, schematics, and parts list). It would have been nice if the rest of the manual was included (disassembly procedure, theory of operation, etc.).
 ;
The Service Manual for the Kenwood KR-V55R provided by owner-manuals.com was as described/advertised. The contents provided the necessary information to effect a diagnosis of the unit. The schematics above all else was instrumental in tracing the the signal flow from component to component.
 ;
This manual was the factory original. Excellent value and contained all the details I needed. Easy dowwnload provided the information when I needed it.
KV-32FV16/32FV26/34FV16/34FV16C/34FX260/34FX260C
2-3. FOCUS
1. Input monoscope signal. 2. Set user controls to normal. 3. Set video mode to STANDARD.
GND
170 + 2.0 Vdc 170Vdc
pedestal
4. Set the PICTURE to maximum. 5. Adjust at 325 Mark for best center/corner focus balance. 6. Receive an entire white signal. Make sure Magenta Ring is at an acceptable level.
2-5. WHITE BALANCE ADJUSTMENTS
NO. 24 25 26 27 28 29 38
Disp. RDRV GDRV BDRV RCUT GCUT BCUT SBRT
Item Red Drive Green Drive Blue Drive Red Cut-off Green Cut-off Blue Cut-off Sub Bright
All Models * 44 38 14:Fix 7 6 6
1. Set program palette to STANDARD and pust RESET.
Focus
2. Input an entire white signal.
Screen (G2)
3. Set to Service Adjustment Mode. 4. Set the PICTURE and BRIGHT to minimum. 5. Adjust with SBRT if necessary.
325 MARK
35 325
6. Set RCUT to "14". 7. Select GCUT and BCUT with 8. Adjust with and and .
35 MARK CENTER CIRCLE
for the best white balance.
9. Set the PICTURE and BRIGHT to maximum. 10. Select GDRV and BDRV with and . then
11. Adjust with 3 and 6 for the best white balance.
2-4. SCREEN (G2)
1. 2. Input dot pattern from the pattern generator. Set the user controls to NORMAL.
12. Write into the memory by pressing .
13. Repeat steps 1-12 for GDR4, BDR4, GCU4 and BCU4 using Video 4 input.
3. Attach the G2-Jig to the C Board. 5. Adjust RCUT, GCUT, BCUT, and SBRT in service mode with an oscilloscope so that voltages on the red, green, and blue cathodes are 170 ± 2.0Vdc. * Use values from Sub Contrast Adjustments NOTE: White balance should be adjusted after Sub Contrast because RDRV is also used in Sub Contrast Adjustment. (See page 22).
5. Observe the screen and adjust SCREEN (G2) VR to obtain the faintly visible background of dot signal. 6. Push the TEST + JUMP (+ Channel) to cut off the signal. The screen should be bright or dark. Brightness of raster must be increased when adjusting. 7. Adjust screen VR until the screen is slightly cut off, or scarcely lights up. A signal cannot be seen when the brightness of the raster is high. 8. Push the JUMP again to release the cut off.
� 13 �
|
|
 |
> |
|