Things You Should Know
6-F Before Requesting Help
Problem The unit does not work. Remedy �Check the settings (1-C). �Charge the battery fully (6-A). �Clean the charge contacts and charge again (6-A). �Install the battery properly (6-B). �Place the handset on the base unit and unplug the AC adaptor to reset. Plug in, and try again. �Re-install the battery and place the handset on the base unit. Try again. An alarm tone sounds. �You are too far from the base unit. Move closer and try again. �Place the handset on the base unit and try again. �Plug in the AC adaptor. �Raise the base unit antennas. �Locate the handset and the base unit away from other electrical appliances (6-D). �Move closer to the base unit. �Raise the base unit antennas. �Press (CH) to select a clearer channel. �The ringer volume is set to OFF. Press � or � while the TALK indicator light is off (2-B). �To answer the call, press (TALK). The program will be canceled. Store the number again. �You cannot store a number while the unit is in the talk mode. �Do not pause for over 60 seconds while storing. �If a power failure occurs, programmed information may be erased. Reprogram if necessary. �If the last number dialed was more than 32 digits long, the number will not be redialed correctly. �The handset is too far from the base unit or is engaged in an outside call. �Charge the battery fully (6-A).
Section 6
6-G Helpful Information
Operating near 2.4GHz electrical appliances may cause interference. Move away from the electrical appliances and/or press the CH (Channel) button. The AC adaptor is used as the main disconnect device, ensure that the AC outlet is located/installed near the unit and is easily accessible. � Environment� do not place the unit in a room where the temperature is less than 5°C (41°F) or greater than 40°C (104°F). Allow 10 cm (4") clearance around the unit for proper ventilation. Avoid excessive smoke, dust, mechanical vibration, shock, or direct sunlight. � Medical�consult the manufacturer of any personal medical devices, such as pacemakers, to determine if they are adequately shielded from external RF (radio frequency) energy. (The unit operates in the frequency range of 2401MHz to 2472MHz, and the power output level can range from 0.001 watts to 0.20 watts.) Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF (radio frequency) energy. � Routine care�wipe the unit with a soft cloth. Do not use benzine, thinner, or any abrasive powder. When you leave the unit unused for a long period of time, unplug the AC adaptor from the outlet. � If there is any trouble� disconnect the unit from the telephone line and connect a known working phone. If the known working phone operates properly, have your unit repaired by one of the authorized Panasonic Factory Service Centers. If the known working phone does not operate properly, consult your telephone company. Caution: To comply with FCC RF exposure requirements, the base unit should be installed with its antenna located at 20 cm or more from persons and handset should be carried with the specific belt-clip provided for the handset to ensure compliance. Other non-tested belt-clips or similar bodyworn accessories may not comply, therefore, should be avoided.
Static, sound cuts in/out, fades. Interference from other electrical units.
The unit does not ring.
While storing a phone number, the unit starts to ring. You cannot store a phone number in memory. Previously programmed information is erased. You cannot redial by pressing (REDIAL).
(HANDSET!LOCATOR) does
Shock-Resistant (HANDSET ONLY)
Although the handset is designed to be shock resistant, do not throw or step on the handset.
Splash-Resistant (HANDSET ONLY)
The handset is designed to be splash resistant. You can use the handset with wet hands. CAUTION: � Do not immerse in water or leave under running water. � Keep the handset away from salt water. � Avoid exposure to prolonged high humidity. � Since water in headset jack may cause damage, close the headset jack cover when the optional headset is not in use. When the optional headset is connected, do not use the handset with wet hands. � If the handset is wet, wipe with a soft dry cloth. � The base unit is not designed to be splash resistant. Do not place the wet handset on the base unit.
not function. The RECHARGE indicator flashes or the unit beeps intermittently. You charged the battery fully, but the RECHARGE indicator flashes. The IN USE/CHARGE indicator light does not go out while charging. If you cannot solve your problem.
�Clean the charge contacts and charge again (6-A). �Install a new battery (6-B). �This is normal.
�Call our customer call center at 1-800-211-PANA(7262). �Panasonic�s e-mail address for customer inquiries:
[email protected] for customers in the USA or Puerto Rico ONLY
