|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A great copy of the manual, and the only one I could find anywhere on the net! The circuit diagrams are easily readable, all component values marked and easy to see. A highly appreciated download!
 ;
Great Manual. This manual is available no where else. It was exactly what I was looking for.
;
The TEAC A-1500's Service Manual was instrumental in reviving this classic reel-to-reel. Not only does it have the schematics, exploded parts diagram and parts list, it also provided mechanical adjustment information that approximate factory default settings.
;
This service manual was determinant to enable to fix my Alpine Amplifier. I am pleased with my purchase. For a 5 star rating I would like to see a higher resolution scan of the printed circuit board lay-out because the gray scale grafics was dificult to see. Also some schematic diagrams were scanned at a slight angle. Never the less, it had all information I needed to troubleshoot and service my equipment.
;
Complete manual, the good quality of reproduction allows enlarged print-out of the schematic diagram in the size it probably had in the original print edition and which is necessary for practical use.
LC-13E1E LC-15E1E
ADJUSTING PROCEDURE OF EACH SECTION
The best adjustment is made before shipping. If any position deviation is found or after part replace is performed, adjust as follows.
Preparation for adjustments
Use the dedicated AC adaptor or stable DC power supply. AC adaptor: UADP-A007WJPZ DC power supply: 12V 4.0A
1. Adjusting procedure
� Checker adjustment Power ON (Adjustment processing mode) � +B adjustment � Counter bias adjustment � TAMP (Contrast) adjustment � White balance adjustment
2. Entering the adjustment processing mode
There are the following two methods. � Setting the pin (81)(KEY4) or pin (82)(KEY5) of IC2001 (microprocessor) to GND, turn on the power. � A �POWER� key is made on with pushing an �TV/VIDEO� and �MENU� keys at the same time.(K of the inspection process mode is displayed by the upper left of the image plane.) � Next, �CH (�)� and �VOL (�)� keys are pushed at the same time.(It becomes the image plane of the adjustment process mode.).....When it is canceled, it is made to turn it off.(Even off in the �MAIN POWER� key, off with R/C are good.)
3. Key operation in the adjustment process mode
� The receiving channel UP/DOWN is performed with the �CH (ù)/(�)� keys. One push ... The UP/DOWN tuning is performed per channel. Continuous push ... The UP/DOWN search is performed until a next receivable station is found. � Various adjustments The adjustment is performed for each item by the �MENU�, �Menu cursor�, �CH (ù)/(�)� or �VOL (+)/(�)� keys (LCD TV set and remote control). � Adjustment item is chosen with the Menu cursor upward/downward keys. � The adjustment item makes a toggle operation with the �MENU� key input. (Next item) If the �MENU� key is input while the bottom item is selected, it moves to the top item on the next page. � Press the auto preset button on the remote controller in the adjustment process mode, and the top item of the next page will show up regardless of which item appears now. Page 1 � Page 2 � ... � Page 24 � Page 1 � Press the manual memory button on the remote controller in the adjustment process mode, and the top item of the same page will show up. � UP/DOWN of each adjustment vale selected is performed with the VOL (+)/(�) keys input. � For P16 � 17, the unit enters the register select mode with the VOL (+)/(�) keys input while NTSC/PAL is selected, and the cursor moves to the address 01. � The cursor moves up or down with the �CH (ù)/(�)� keys and moves left or right with the VOL (+)/(�) keys, and a decision is made with the 12 key. When the decision is made, the cursor moves to the adjustment value selected, and UP/DOWN of each adjustment value selected by the �VOL (+)/(�)� keys input is performed. 0 � 1 � ... � 9 � A � ... � F � 0 � ... Decide with the 12 key and return to the address select. Move to the next item with the �MENU� key. During address select, the cursor movement by the �VOL (+)/(�)� keys input is as follows: Example: 01 � 02 � 03 � 01 � ... The cursor movement by the �CH (ù)/(�)� keys input is as follows: Example: 02 � 05 � ... � F6 � 02 � ...
12
|
|
|
> |
|
