|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ filippo611@aol.com
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
LC-20B2EA
ADJUSTING PROCEDURE OF EACH SECTION
The best adjustment is made before shipping. If any position deviation is found or after part replace is performed, adjust as follows.
Preparation for adjustments
Use the dedicated AC adaptor or stable DC power supply. LC20E1E AC adaptor: UADP-0241CEPZ DC power supply: 13V 5.4A
1. Adjusting procedure
� Checker adjustment Power ON (Adjustment processing mode) � +B adjustment � Counter bias adjustment � TAMP (Contrast) adjustment � White balance adjustment
2. Entering the adjustment processing mode
There are the following two methods. � Setting the pin (81)(KEY4) or pin (82)(KEY5) of IC2001 (microprocessor) to GND, turn on the power. � A �POWER� key is made on with pushing an �TV/VIDEO� and �MENU� keys at the same time.(K of the inspection process mode is displayed by the upper left of the image plane.) � Next, �CH (�)� and �VOL (�)� keys are pushed at the same time.(It becomes the image plane of the adjustment process mode.).....When it is canceled, it is made to turn it off.(Even off in the �MAIN POWER� key, off with R/C are good.)
3. Key operation in the adjustment process mode
� The receiving channel UP/DOWN is performed with the �CH (ù)/(�)� keys. One push ... The UP/DOWN tuning is performed per channel. Continuous push ... The UP/DOWN search is performed until a next receivable station is found. � Various adjustments The adjustment is performed for each item by the �MENU�, �Menu cursor�, �CH (ù)/(�)� or �VOL (+)/(�)� keys (LCD TV set and remote control). � Adjustment item is chosen with the Menu cursor upward/downward keys. � The adjustment item makes a toggle operation with the �MENU� key input. (Next item) If the �MENU� key is input while the bottom item is selected, it moves to the top item on the next page. � Press the auto preset button on the remote controller in the adjustment process mode, and the top item of the next page will show up regardless of which item appears now. Page 1 � Page 2 � ... � Page 22 � Page 1 � Press the manual memory button on the remote controller in the adjustment process mode, and the top item of the same page will show up. � UP/DOWN of each adjustment vale selected is performed with the VOL (+)/(�) keys input. � For P16 � 17, the unit enters the register select mode with the VOL (+)/(�) keys input while NTSC/PAL is selected, and the cursor moves to the address 01. � The cursor moves up or down with the �CH (ù)/(�)� keys and moves left or right with the VOL (+)/(�) keys, and a decision is made with the 12 key. When the decision is made, the cursor moves to the adjustment value selected, and UP/DOWN of each adjustment value selected by the �VOL (+)/(�)� keys input is performed. 0 � 1 � ... � 9 � A � ... � F � 0 � ... Decide with the 12 key and return to the address select. Move to the next item with the �MENU� key. During address select, the cursor movement by the �VOL (+)/(�)� keys input is as follows: Example: 01 � 02 � 03 � 01 � ... The cursor movement by the �CH (ù)/(�)� keys input is as follows: Example: 02 � 05 � ... � F6 � 02 � ...
10
|
|
|
> |
|
