|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
 ;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
 ;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
 ;
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
LC-26GA5E LC-37GA5E LC-32GA5E
Troubleshooting Table (continued)
No picture in the LCD section
Is the power supplied to the LCD CONTROLLER PWB? (P7707: +6/+4/+13V) Check if the REG output -D3.3V_1/2 of IC7706/IC7704 (REG-IC) is sent properly.
YES
Is the output signal of IC4601 (GAMMA) sent properly?
NO
YES
Adjustment process menu: Is the gradation pattern displayed properly when setting "PATTERN1" in the second llayer of "LCD CONT" to "02"?
Check the FFC (LV, SC2201 - SC4601) between MAIN PWB and LCD CONTROLLER PWB and input circuit of IC4601. Check IC4501 (LCD CONTROL) and its peripheral circuits.
NO
YES
Check IC4901 (QS-DRIVER) and its peripheral circuits.
Data bit drop (gradation-related)
Adjustment process menu: Is the gradation pattern displayed properly when setting "PATTERN1" in the second layer of "LCD CONT" to "02"?
NO
Check the connection between SC4651 and SC4652 and peripheral circuits of IC4501 (LCD CONTROL).
YES
Adjustment process menu: Is the gradation pattern displayed properly when setting "PATTERN2" in the second layer of "LCD CONT" to "1"?
NO
Check IC4902 (FIFO) and its peripheral circuits.
YES
Check IC4601 (GAMMA) and its peripheral circuits.
Noise is caused to the moving picture with the QS drive on.
Is the input voltage at pin (62) (OS-TEMP) of IC2004 (microprocessor) 5V?
NO
Check IC4901 (QS-DRIVER) and its peripheral circuits.
YES
Is the harness connected correctly between the inverter GND PWB and LCD CONTROLLER PWB?
NO
Connect the harness correctly or replace it.
YES
The thermistor on the INVERTER GND PWB is faulty. Or check the peripheral circuits.
The whole screen is whitish (LCD power supply).
YES
Adjustment process menu: Is the gradation pattern displayed properly when setting "PATTERN2" in the second layer of "LCD CONT" to "1"? (Is it whitish or dark?) Check the video signal circuits (IC4501, IC4901, IC4601).
NO
Disconnect the FPC from SC4651 and SC4652. (To protect the panel against damage)
YES
Check the power supply voltage supplied to the panel (check at SC4651 and SC4652).
46
|
|
 |
> |
|