|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
;
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
 ;
It`s full copy of a service manual from url http://www.philips.owner-manuals.com/PM3216-service-manual-PHILIPS.html
;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
English
6. SET UP
POSITIONING THE PROJECTOR AND SCREEN � Place the projector on a stable, level surface, out of direct sunlight and away from sources of excessive dust, dirt, heat, water, moisture, vibration and strong magnetic fields. Face the projector towards the screen for the best picture results. To determine the distance for the desired size, please refer to the Projection Assistant, a calculation programme included on the CD-ROM.
Video
S-Video in
Video in
L Audio R
Audio
Power
Data
Mouse
Data in
out Audio in
3. Press the STANDBY ON/OFF button to switch on the projector. � The lamp indicator flashes green and the start-up screen appears for 5 seconds. � When the projection lamp is PHILIPS on, the lamp indicator lights up Multimedia Projectors green. � The start-up position of the projector depends on when the projector has been switched off before. The factory default position is Power/Standby. 4. To switch off the mains supply completely, pull the mains
plug out of the wall socket.
� The screen should be positioned so that it is not directly touched by sunlight or artificial light, as this will wash out the colours of the picture, making it hard to see. � The projector can be used for both front projection, rear projection and ceiling projection applications. As default factory setting, the projector has been set up for front projection. You can change to rear or ceiling projection via the OSD menu. See �Rear screen projection� and �Upside-down (ceiling) projection� under �Other settings� for further instructions. � Choose a screen size suitable for the number of viewers and the size of the room. � Picture quality is best when you sit directly in front of the projector screen. MAINS SUPPLY
Note: Before disconnecting the mains lead, make sure that the cooling fan has stopped (about 3 minutes after the projector has been switched to Power Standby).
ADJUSTING THE FOCUS AND SIZE OF THE IMAGE � Use the ZOOM ring to adjust the size of the image. � Use the FOCUS ring to adjust the focus of the image.
On/Of f
Standby Lamp Mute RC Volume
Zoom ring Focus ring
Menu
Data
Video
AVMute te
OK
1. Insert the mains lead into the projectors POWER socket and connect it to the wall socket. Note: The standby indicator lights up red, the projector is now in the Power/Standby mode. 2. Remove the lens cap.
in
Video in L Audio R
Audio
se Data in
out Audio in
Power
On/Off
Standby Lamp Mute RC
Video Vid
Data AVMute te
Volume
Menu
OK
ADJUSTING THE VERTICAL AND HORIZONTAL ANGLE OF THE PROJECTOR
Video
S-Video in Video in L Audio R
Data
Mouse Data in in
Audio
Power
Vertical angle � Use the Height/Level Adjuster to adjust the vertical angle of the projector as specified under �Positioning the projector and screen�.
in Audio out
To Raise: press the adjuster carefully and lift to raise the projector. To Lower: press the adjuster carefully again to lower the projector. � Use the FOCUS Ring and ZOOM Ring to readjust the focus and size of the image.
8
|
|
|
> |
|
