|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a service manual in every sense of the word ( French and German versions of the text are included, as well as English..)
There are explanations of the mechanical and electrical functions, plenty of mechanical drawings, and the needed schematics. The quality of the scanning is excellent - all the component values are clearly legible - and very usefully there are pcb component layouts, so you can find a component on the schematic, and then very quicky pinpoint its physical location on the relevant pcb.
I cannot see how I can give this manual any less than the maximum 5 stars! Great value for money, which will pay for itself immediately. Excellent all round!
;
the manual is great and especially hard to find... thanks for the great service and having a hard to find manuel_
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.50 of store credit for Your review.
;
hat alles sehr gut geklappt. Das Servicemaual ist gut zu verwenden. Die Pläne und Schrift
ist klar und leserlich. Außerdem preiswert. Grüße an alle Hifi-Bastler
;
I got the manual quickly after the payment was transfered (1 day). The manual was exactly what i needed and the updates via e-mail were great. Thanx!
s Installing the ICC profile
Installing the monitor�s ICC profile. (If the set-up information has already been installed, so too has the profile, and there is no need to install it.) This explanation assumes that the floppy disk drive is �A drive�. 1. Place the Utility Disk in the computer�s A drive. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings] and [Advanced]. 5. Click on [General] and from [Compatibility] select [Apply the new display setting without restarting], then click on [Color Management]. 6. Click [Add], and select [3 1/2 Floppy [A:]] as the file location. 7. Choose the color profile that you would like to install, and click on [Add]. 8. Choose the profile and click on [Set As Default]. 9. Click [OK], and close the window. 10. Remove the Utility Disk from the A drive. � When using the ICC profile, please set the [WHITE BALANCE] to [STD].
4. Being careful not to damage the monitor, spread out a soft cloth and lay the monitor on it display-side down.
5. Attach the arm to the monitor with four screws.
Information The screws used to attach the arm should be M4 screws with a length of 4 mm ~ 6 mm protruding from the surface to be attached. Using any other kind of screw may lead to the monitor falling off or damage to the internal part of the monitor.
4 ~ 6 mm
Screw used to attach arm Arm Part of monitor to which arm is attached
3. INSTRUCTIONS FOR INSTALLING A VESA COMPLIANT ARM
An arm based on the VESA standard can be attached to the monitor. The arm must be purchased separately. When choosing the arm to be installed please take note of the following points. � The arm should be compatible with the VESA standard, and there must be a gap of 75mm u 75mm between the screw holes on the section to be attached. � The arm must not fall off or break off after being attached to the monitor. Note: Do not overly bend the cable or add extension cords as this could lead to malfunction. 1. Ensure that both the monitor and computer are switched off. 2. Remove the AC adapter and the RGB signal cable. 3. Press down on the stand and gently fold back the monitor. Be sure to completely fold the monitor back to stopping point. If it is attempted to install the arm while the monitor is not completely folded back, the monitor may suddenly fall, leading to malfunction.
6. Connect the AC adapter and the RGB signal cable.
Be careful not to pinch your fingers.
LL-T15G1/E15G1 CONNECTION, ADJUSTMENT, OPERATION AND FUNCTIONS
2�3
|
|
|
> |
|
