|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
SECTION 3 DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE CAUTION AT DISASSEMBLY: � Make sure that the power cord is disconnected from the outlet. � Pay special attention not to break or damage the parts. � When removing each board, remove the connectors as required. Taking notes of the connecting points (connector numbers) makes service procedure manageable. � Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors. 3.1.1 REMOVING THE STAND (1) Remove the JACK COVER. (2) Remove the 2 screws [A], then remove the STAND COVER. (3) Remove the 2 screws [W], then remove the CABLE COVER. (4) Remove the 4 screws [B], then remove the STAND. 3.1.2 REMOVING THE REAR COVER � Remove the STAND. (1) Remove the 8 screws [C], 1 screw [D] and 2 screws [E], then remove the REAR COVER. 3.1.3 REMOVING THE POWER PWB � Remove the STAND. � Remove the REAR COVER. (1) Remove the 4 screws [G] and 1 screw [H], then remove the TERMINAL BASE. (2) Remove the 8 screws [F], then remove the BACK BRACKET. (3) Remove the 6 screws [J], then remove the POWER PWB SHIELD. (4) Remove the 5 screws [K], then remove the POWER PWB. 3.1.4 REMOVING THE MAIN PWB � Remove the STAND. � Remove the REAR COVER. � Remove the TERMINAL BASE. � Remove the BACK BRACKET. � Remove the POWER PWB SHIELD. (1) Remove the 7 screws [L] and 2 screws [N], then remove the MAIN PWB SHIELD. (2) Remove the 6 screws [M], then remove the MAIN PWB. 3.1.5 REMOVING THE KEY PWB � Remove the STAND. � Remove the REAR COVER. (1) Remove the 2 screws [P], then remove the KEY PWB. 3.1.6 REMOVING THE LED PWB � Remove the STAND. � Remove the REAR COVER. (1) Remove the 2 screws [Q], then remove the LED PWB. 3.1.7 REMOVING THE SPEAKER � Remove the STAND. � Remove the REAR COVER. (1) Remove the 6 screws [R], then remove the SPEAKER (L/ R). CAUTION: Please do not disassembly the SPEAKER. When the speaker is decomposed, the performance cannot be kept. 3.1.8 REMOVING THE LCD PANEL UNIT � Remove the STAND. � Remove the REAR COVER. � Remove the TERMINAL BASE. � Remove the BACK BRACKET. (1) Remove the 6 screws [S], then remove the MAIN BASE. (2) Remove the 6 screws [T], then remove the FRONT PANEL. (3) Remove the 2 screws [U], then remove the TOP FRAME. (4) Remove the 2 screws [V], then remove the BOTTOM FRAME. NOTE: � Pay special attention not to break or damage on the FRONT PANEL. � The LCD PANEL UNIT is fixed to the FRONT PAMEL (at the back side)by using double-side adhesive tapes. To remove the LCD PANEL UNIT, remove the adhesive tape on the FRONT PANEL slowly.
1-10 (No.YA314)
|
|
|
> |
|
