|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
 ;
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
;
Fast service, document is OK. Thanks! Searched for it long time.
;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
6-32 x 5/8 Long Phillips Head Screws
Figure 4: Camera/Fixed Lens Mounting Position Zoom Lens Cameras: Use same procedure as fixed lens cameras. All hardware shown below must be used. See Figure 4a.
W9407400BE
Figure 1: Remove Phillips Head Screws 2. Remove the end cap from the housing by pulling out the cradle assembly. See Figure 2.
Mounting Position For Cameras With TC9948 6X Zoom Lens. Use 1/4-20 x 1/2-Inch Screw Provided. Be Sure Plastic Washer Is In Place. Mounting Position For TC9948 6X Zoom Lens. Use 1/4-20 Screw Provided.
W9407404AE
W9407401AE
Figure 4a: Camera/Zoom Lens Mounting Positions LTC 9353/00 and LTC 9358/00 Only Note: Refer to section 5a for LTC 9352/01 model power wiring instructions. 5. When installing 120 or 220 volt cameras, the camera power cord must be cut leaving enough cable to strip and attach to the terminal block. Strip no less than 6 mm (1/4 in) and no more than 8 mm (5/16 in) of insulation away from the wires, making sure not to nick the wires. Attach the wires to the terminal block. See Figure 5 and Figure 6. Insert the loose end of the power supply cable or the remainder of the camera power cord through the lower right fitting. The fitting accepts cables with diameters from 1.8 mm (0.07 in) to 6.6 mm (0.26 in). Tie a figureeight knot in the wire to prevent strain on internal circuits. Repeat the same procedure for stripping the wires. Attach the wires to the opposite side of the terminal block. Crimp the ground wire to the ground lug located on the reverse side of the cradle. See Figure 5 and Figure 6.
CCD Camera Rear Cap
Figure 2: Remove Cradle Assembly 3. Place the camera/lens on the cradle assembly. Thewith a correct positioning for mounting either a camera fixed lens or a camera with a zoom lens is shown in Figure 3.
W9407402AE
Figure 3: Camera/Lens Mounting Positions 4. Fixed Lens Cameras: Secure the camera/lens to the cradle with the 1/4-20 x 1/2-inch screw, nylon bushing, 5/16-inch flat washer, and 2.5 mm (0.100 inch) plastic washer. Make sure the thermoplastic shield is under the camera in the correct position. Be sure that the nylon bushing is in place. All hardware shown below must be used. For LTC 0240 Series cameras, use 1/4-20 x 7/8 inch BHCS, nylon bushing, 5/16-inch flat washer, and 9.8 mm (0.385 inch) plastic spacer. See Figure 4.
2000 Max. 250 Min.
250 Min.
Cradle
W9407405AE
Figure 5: Cut Camera Power Cord Note: If power is supplied from a pan/tilt feed thru, follow the same instructions as above for wiring procedures. Figure 6 shows the relationship with color codes. Hint: For ease of wiring, remove the terminal block from its mounted position. Wire accordingly and remember to maintain polarity. Remount the terminal block with the wires in place. See Figure 6.
Plastic Washer
5/16 Inch Flat Washer Nylon Bushing 1/4-20 x 1/2 Screw
W9407403AE
Mounting Position For Camera With Fixed Lens. Use 1/4-20 x 1/2 Screw
4
|
|
|
> |
|
