|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This document is just what I was looking for, it´s very useful, it contains adjustment procedures for the final stage of the power amp and also
has a complete wiring diagram and description of the main semiconductors used in the design.
;
Dear Sirs,
Thank you for the fast support, the manual does provide all necessary information to repair the radio. All schematics are in a good quality for reading.
The manual fits 100% to my requirements as a technican.
Kind regards Thomas
;
the big video recorder format s-vhs many features delicate in loading system of the cassette. Such machines are no longer manufactured, it would be too expensive.
 ;
THIS MANUAL IS VERY GOOD AND VERY CLEAR
PLEASE NOTE IT DOES NOT CONTAIN THE SETUP INFORMATION TO ALIGHN THE GEARS IN THE CD MECH IT DOES SHOW ALL THE PARTS AND THEIR LOCATIONS .
;
Complete service and operation manual. All schematics are there, all circuit boards AND add-on boards. Including exploded views ,component names and specifications. Also electrical and mechanical adjustment procedures are in this manual. This manual also covers the more advanced BR-S811E unit. Scan quality is fair and usable.
Alignment and Adjustments
2. Cassette Deck
2-1. To Adjust Tape Speed
Notes 1) Measuring tape: i) MTT-111 (or equivalent) (Tapes recorded with 3kHz) ii) MTT-5512 (or equivalent) 2) Connect the SPK OUT of the MAIN PCB to the frequency counter as in figure 1-5.
MAIN PCB SPK OUT output Figure 1-5 Frequency Counter
2-2. To Adjust PlayBack Level/REC
Notes 1) Before the actual adjustment, clean the play/recording head. 2) Measuring tape : i) MTT-114N(or equivalent 10kHz AZIMUTH control) ii) MTT-5512 3) The cassette deck is connections as shown in figure 1-7.
Step
Item
Pre-Setup Condition
Pre-Setup 1) Deck 1:MTT-111 2) Press PLAY SW button 3) Deck 2:Same as above
To Adjust
Standard
Remark
1. Adjust Deck 1 Play Level
Turn VSR1 to left and right (FRONT PCB) 3KHz ±1% range Step Item Pre-Setup Condition Pre-Setup After putting MTT AZIMUTH SPK OUT (VTVM is connected to the scope)
MAIN PCB
SPK OUT
VTVM
1
NOR SPEED Control
SPK OUT (connected to the frequency counter)
To Adjust
Standard
Remark
114N into Deck 1 - Press FWD PLAY button.
1
Recording /Play head Oscilloscope
- T the control urn screw to as shown in Figure 1-6.
Max output and same phase (both channels)
After adjustment secure it with REGION LOCK.
(GND)
In Out Figure 1-7
2. Adjust Deck 2 Play Level/ REC BIAS
Step Item Pre-Setup Condition
SPK OUT
AZIMUTH control screw
(RVS Play)
AZIMUTH control screw
(FWD Play)
Pre-Setup After putting MTT 114N into Deck 2 - Press FWD PLAY button.
To Adjust
Standard
Remark
Figure 1-6
1 AZIMUTH
(VTVM is connected to the scope)
- T the control urn screw to as shown in Figure 1-6.
MAX OUTPUT and same phase (both channels)
After adjustment secure it with REGION LOCK.
Audio OSC.
SET (MAIN PCB)
VTVM
Oscilloscope
After putting MTT -
2
IN AUX IN TP SPK OUT
Recording Bias Voltage
5512 into Deck 2 Fig 1-8
1) Press REC PLAY button. 2) T APE PCB JCW3 ,connected
- T JSR2L,JSR2R urn to the right and left
CHECK TO 7mV(±0.5mV)
IN OUT
to VTVM
Figure 1-8
Samsung Electronics
1-3
|
|
|
> |
|
