|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a great site. I placed my order and by the next am it was available for download. Had some problems with some missing copy on some pages. Once I brought the error to the OMC's attention, the issue was resolved. I'll come back again.
 ;
Mi spiace per non poter scrivere in inglese... ma sono veramente soddisfatto del servizio offerto. Grazie..!!
;
The quality of this manual is good. It has all schematics and setup information for both the MDS-B3 and the MDS-B4. The scan quality is quite good, all pages are readable, This service manual also contains scans of the operating instructions from the User manual.
;
Quick site processing. A complete and very useful manual with all details. Thank you!
;
Das Service Manual war von der ersten bis zur letzten Seite sehr informativ und hilfreich. Die Darstellung aller Teile war klar und der Text gut lesbar.
Vielen Dank, das war nicht der letzte Download bei ownner-manuals.com.
Alignment and Adjustments
2. Cassette Deck
2-1. To Adjust Tape Speed
Notes 1) Measuring tape: i) MTT-111 (or equivalent) (Tapes recorded with 3kHz) ii) MTT-5512 (or equivalent) 2) Connect the SPK OUT of the MAIN PCB to the frequency counter as in figure 1-5.
MAIN PCB SPK OUT output Figure 1-5 Frequency Counter
2-2. To Adjust PlayBack Level/REC
Notes 1) Before the actual adjustment, clean the play/recording head. 2) Measuring tape : i) MTT-114N(or equivalent 10kHz AZIMUTH control) ii) MTT-5512 3) The cassette deck is connections as shown in figure 1-7.
Step
Item
Pre-Setup Condition
Pre-Setup 1) Deck 1:MTT-111 2) Press PLAY SW button 3) Deck 2:Same as above
To Adjust
Standard
Remark
1. Adjust Deck 1 Play Level
Turn VSR1 to left and right (FRONT PCB) 3KHz ±1% range Step Item Pre-Setup Condition Pre-Setup After putting MTT AZIMUTH SPK OUT (VTVM is connected to the scope)
MAIN PCB
SPK OUT
VTVM
1
NOR SPEED Control
SPK OUT (connected to the frequency counter)
To Adjust
Standard
Remark
114N into Deck 1 - Press FWD PLAY button.
1
Recording /Play head Oscilloscope
- T the control urn screw to as shown in Figure 1-6.
Max output and same phase (both channels)
After adjustment secure it with REGION LOCK.
(GND)
In Out Figure 1-7
2. Adjust Deck 2 Play Level/ REC BIAS
Step Item Pre-Setup Condition
SPK OUT
AZIMUTH control screw
(RVS Play)
AZIMUTH control screw
(FWD Play)
Pre-Setup After putting MTT 114N into Deck 2 - Press FWD PLAY button.
To Adjust
Standard
Remark
Figure 1-6
1 AZIMUTH
(VTVM is connected to the scope)
- T the control urn screw to as shown in Figure 1-6.
MAX OUTPUT and same phase (both channels)
After adjustment secure it with REGION LOCK.
Audio OSC.
SET (MAIN PCB)
VTVM
Oscilloscope
After putting MTT -
2
IN AUX IN TP SPK OUT
Recording Bias Voltage
5512 into Deck 2 Fig 1-8
1) Press REC PLAY button. 2) T APE PCB JCW3 ,connected
- T JSR2L,JSR2R urn to the right and left
CHECK TO 7mV(±0.5mV)
IN OUT
to VTVM
Figure 1-8
Samsung Electronics
1-3
|
|
|
> |
|
