|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
Alignment and Adjustments
2. Cassette Deck
2-1. To Adjust Tape Speed
Notes 1) Measuring tape: i) MTT-111 (or equivalent) (Tapes recorded with 3kHz) ii) MTT-5512 (or equivalent) 2) Connect the SPK OUT of the MAIN PCB to the frequency counter as in figure 1-5.
MAIN PCB SPK OUT output Figure 1-5 Frequency Counter
2-2. To Adjust PlayBack Level/REC
Notes 1) Before the actual adjustment, clean the play/recording head. 2) Measuring tape : i) MTT-114N(or equivalent 10kHz AZIMUTH control) ii) MTT-5512 3) The cassette deck is connections as shown in figure 1-7.
Step
Item
Pre-Setup Condition
Pre-Setup 1) Deck 1:MTT-111 2) Press PLAY SW button 3) Deck 2:Same as above
To Adjust
Standard
Remark
1. Adjust Deck 1 Play Level
Turn VSR1 to left and right (FRONT PCB) 3KHz ±1% range Step Item Pre-Setup Condition Pre-Setup After putting MTT AZIMUTH SPK OUT (VTVM is connected to the scope)
MAIN PCB
SPK OUT
VTVM
1
NOR SPEED Control
SPK OUT (connected to the frequency counter)
To Adjust
Standard
Remark
114N into Deck 1 - Press FWD PLAY button.
1
Recording /Play head Oscilloscope
- T the control urn screw to as shown in Figure 1-6.
Max output and same phase (both channels)
After adjustment secure it with REGION LOCK.
(GND)
In Out Figure 1-7
2. Adjust Deck 2 Play Level/ REC BIAS
Step Item Pre-Setup Condition
SPK OUT
AZIMUTH control screw
(RVS Play)
AZIMUTH control screw
(FWD Play)
Pre-Setup After putting MTT 114N into Deck 2 - Press FWD PLAY button.
To Adjust
Standard
Remark
Figure 1-6
1 AZIMUTH
(VTVM is connected to the scope)
- T the control urn screw to as shown in Figure 1-6.
MAX OUTPUT and same phase (both channels)
After adjustment secure it with REGION LOCK.
Audio OSC.
SET (MAIN PCB)
VTVM
Oscilloscope
After putting MTT -
2
IN AUX IN TP SPK OUT
Recording Bias Voltage
5512 into Deck 2 Fig 1-8
1) Press REC PLAY button. 2) T APE PCB JCW3 ,connected
- T JSR2L,JSR2R urn to the right and left
CHECK TO 7mV(±0.5mV)
IN OUT
to VTVM
Figure 1-8
Samsung Electronics
1-3
|
|
|
> |
|
